3
4
Sensing object
Sensing
object
Sensing
object
Moving
direction
Moving
direction
Moving
direction
Precautions during installation
Name of each part
Characteristic of sensing distance
Operation chart
Mode setting switch
D.ON : Dark ON
L.ON : Light ON
Stability
indicator(GREEN)
Output
indicator (RED)
Distance
setting indicator
Distance
setting volume
•Colored paper sensing distance
•Material sensing distance
When setting the sensing distance of white paper as 200 cm
When setting the sensing distance of white paper as 100 cm
When setting the sensing distance of white paper as 20 cm
When setting the sensing distance of white paper as 200 cm
When setting the sensing distance of white paper as 100 cm
When setting the sensing distance of white paper as 20 cm
distance
distance
White
Red
Green
Blue
Gray
Black
Black color paper
Rubber
Packing box
Veneer boar
d
White color paper
When setting the sensing distance of white paper as 200 cm
When setting the sensing distance of white paper as 100 cm
When setting the sensing distance of white paper as 20 cm
When setting the sensing distance of white paper as 200 cm
When setting the sensing distance of white paper as 100 cm
When setting the sensing distance of white paper as 20 cm
distance
distance
White
Red
Green
Blue
Gray
Black
Black color paper
Rubber
Packing box
Veneer boar
d
White color paper
Stability indicator (Green)
Control output (TR)
Output indicator (Red)
Stability indicator (Green)
Control output (TR)
Output indicator (Red)
Stability indicator (Green)
Control output (TR)
Output indicator (Red)
Stability indicator (Green)
Control output (TR)
Output indicator (Red)
Stability indicator becomes ON when an amount of light exceed the operation level and
becomes 120% (stable L.ON area). It can be used as the environmental change after setup
or level down during operation and initial operation check.
<L.ON operation>
<D.ON operation>
How to set the distance
No
How to set the distance
Setting state
Indicator for display
the setting distance
1
Remove the sensing object and
turn the distance setting volume
to Max direction until right before
the operation indicator becomes
ON. Here, we will refer this
position as the position A. If
operation indicator does not
becomes ON then we will refer
the maximum position as A.
2
Place the sensing object in the
sensing position and check
whether the operation indicator
and stability indicator become ON.
After inspecting such things, turn
the setting volume to Min direction
until the operation indicator
becomes OFF. We will refer this
position as the position B.
3
Set the indicator of distance
setting to fall in between A and
B by turning the distance setting
volume to Max direction and
checks whether it is operating
properly. Here, if the stability
indicator (green) does not
becomes ON even after sensing
a certain object then the cause
is maybe due to the unstable
sensing so please re-check the
sensing method.
Photo-electric switch
Photo-electric switch
Photo-electric switch
Background
object
Background
object
Background
object
Sensing object
Sensing object
Sensing object
Photo-electric switch
Photo-electric switch
Photo-electric switch
Background
object
Background
object
Background
object
Sensing object
Sensing object
Sensing object
Photo-electric switch
Photo-electric switch
Photo-electric switch
Background
object
Background
object
Background
object
Sensing object
Sensing object
Sensing object
(A)
3
5
1
1
3
5
3
(B)
(B)
(A)
(A)
3
5
1
1
3
5
3
(B)
(B)
(A)
(A)
3
5
1
1
3
5
3
(B)
(B)
(A)
①
②
· Please use ⊖ driver as above picture when you detach top cover from the case.
· Regarding the installation direction of photo sensor, please consider about the moving
direction of sensing object and install it (please refer to an image below)
Sensing object
Object with good reflectivity
✽ If an object with good reflectivity is in present under the photo
sensor then operation may become unstable. Therefore, please
slant the sensor and place it just like an image below or have a
gap between the ground and sensor.
·Please do not let strong ray light such as sunlight, fluorescent light, incandescent
lamp and etc to fall within the directional angle of photo sensor.
·When installing the photo sensor, do not apply strong force on it by using tools
such as hammer and etc. Doing so may damage the internal functions.
·Please use M4 for screw
·The tightening torque of screw should be less than 1.2 N·m