▍Specification
▍Dimension
[Unit : mm]
Model
Low
HSR-SLD152Z
HSR-SLD252Z
HSR-SLD402Z
High HSR-SLD154Z
HSR-SLD254Z
HSR-SLD404Z
Rated Load
Voltage
Low
90 - 264 V a.c.
High
90 - 480 V a.c.
Peak Voltage
(Non-repetition)
Low
600 V
High
800 V
1,200 V
Rated load current
15 A
25 A
40 A
Frequency
50/60 ㎐(Dual usage)
Input current 60 Hz
(8.3 ms non-recurring)
Low
170 A
260 A
420 A
High
170 A
250 A
370 A
Input current 50 Hz
(10 ms non-recurring)
Low
160 A
250 A
400 A
High
160 A
230 A
350 A
Leakage current
20 ㎃ max
Output ON voltage dropping
1.6 V (R.M.S) max
Rated Voltage
5 - 24 V d.c.
Operating Voltage Range
4 - 32 V d.c.
Impedance
Less than 4 ㏀
Operation Voltage
More than 3 V d.c.
Reset Voltage
Less than 1.5 V d.c.
Input Current
Constant-current system : 8 ㎃ (±3)
Response Time
1/2 Cycle + 1 ms max. (“R” type below 1 ms)
Insulating Resistance
500 V d.c., 100 ㏁ (Between the input / output and case)
Dielectric strength
3,000 V a.c. (For 1 min at 60 ㎐)
Vibration resistance
10 - 55 ㎐, Double amplitude : 1.5 ㎜ each X,Y and Z
direction for 2 hours
Shock resistance
1,000 ㎨, X·Y·Z each axis 3 times
Storage Temperature
-30 ~ 90 ℃
Ambient Temperature
-5 ~ 40 ℃ (But without frostiness)
Ambient Humidity
45 ~ 85 % RH
Pollution rate
2nd rating
Purpose of use
Resistance/Inductive load
Accepted standard
IEC 62314
Weight (Including box)
Approx 230g
Approx 372g
▍Safety information
• The input/output terminals are subject to electric shock risk.
Never let the input/output terminals come in contact with your body or conductive substances.
DANGER
•Before you use, please read safety precautions carefully, and use this product properly.
• If you are concerned about serious accident due to the malfunction of products,
please install the external safety equipment
• To prevent defection or malfunction of this product, supply proper power voltage in
accordance with the rating.
• To prevent electric shock or devise malfunction of this product, do not supply the
power until the wiring is completed.
• Reassemble this product while the power is off. Otherwise, it may cause malfunction or electric shock.
• If the user uses the product with methods other than specified by the manufacturer,
it will brings the bodily injuries or property damages.
• Due to the danger of electric shock, please use this product installed onto a panel while
an electric current is applied.
WARNING
• Before using the product you have purchased, please check out if it is exactly what you ordered.
• Do not use this product at any place with corrosive gas (especially noxious gas or ammonia) or
flammable gas.
• Do not use this product at any place with liquid, oil, medical substances, dust, salt or iron contents.
• Do not use this product at any place with excessive induction trouble, static electricity or magnetic noise.
• Do not use this product at any place with possible thermal accumulation due to direct sunlight or heat radiation.
• When the product gets wet, the inspection is essential because there is a danger of an electric
leakage or fire.
•Do not connect anything to the unused terminals.
•For DC types, please connect wires at the correct position after checking polarity of terminal.
•When product is disposed, treat as a industrial waste.
•Since a heat sink corner is sharp, it would lead to a serious injury.
• When electricity flows, desktop or heat sink's corner temperature would be high so that it could
lead people to suffer burns.
•When it is out of order, please separate SSR from head sink and change only SSR.
•This model has epoxy molding for the purpose of safety, reliability and extends of the life.
• When applying an electric current, SSR is heated more and more. So, it has more durable at low
heat sink temperature and ambient temperature.
CAUTION
DANGER
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury
CAUTION
CAUTION indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury
Before using the product, please read the safety information thoroughly and use it properly. Alerts declared
in the manual are classified to Danger, Warning and Caution by their criticality.
LO
AD
INPUT
■ Measurement for CE certified products
Single-Phase Solid State Relay
HSR-SL
Thank you for purchasing HANYOUNG product.
Please check whether the product is the exactly same as you ordered.
Before using the product, please read this instruction manual carefully.
Please keep this manual where you can view at any time
INSTRUCTION MANUAL
28, Gilpa-ro 71beon-gil, Michuhol-gu,
Incheon, Korea
TEL : +82-32-876-4697
http://www.hanyoungnux.com
HANYOUNGNUX CO.,LTD
HEAD OFFICE
MC0501KE210119
● HSR-SLD15
□
HSR-SLD25
□
● HSR-SLD2C15□
● HSR-SLD40
□
17.4
4.5
5.5
90
99
4.5
44.4
98.5
17.4
4.5
5.5
90
99
4.5
22.4
17.4
4.5
5.5
90
99
4.5
45.4
※ 2 contact : Only available for 15 A items (HSR-SLD2C152Z, HSR-SLD2C154Z)
▍Suffix code
Model
Code
Description
HSR-SL
□ □ □ □ □ -□ Slim Type Single-Phase Solid State Relay
Input voltage D
4 - 32 V d.c.
Contact
-
1 contact (No mark)
2C
2 contacts (Only for 15 A)
Rated load current
15
15 A
25
25 A
40
40 A
Rated load voltage
2
90 - 264 V a.c. (Low)
4
90 - 480 V a.c. (High)
Operation method
Z
Zero Cross Switching (Standard)
R
Random Switching
Option
-
None (No mark)
BI 60 °C, 80 °C Bimetallic Mounting
Model
Code
Description
HSR-SL
□ □ □ □ □ -S Slim Type Single-Phase Solid State Relay
Input voltage D
4 - 32 V d.c.
Contact
-
1 contact (No mark)
Rated load current
15
15 A
25
25 A
40
40 A
Rated load voltage
2
90 - 264 V a.c. (Low)
4
90 - 480 V a.c. (High)
Operation method
Z
Zero Cross Switching (Standard)
■ S-MARK certified products
■ CE certified products