Hansa C40 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 28

Hansa C40 Скачать руководство пользователя страница 14

Hansa C40 O&M Manual

– OM-013 Revision E 23/10/19

© Hansa Chippers 2019

12

Reinstall the knives:

Clean all mounting surfaces and remount the knives
in the reverse procedure. Torque the knife clamping
nuts up to 190 Nm.

After sharpening, the width of the knives will have
been reduced, therefore the gap between the knives
and anvil may require adjustment. There should be
3 mm of clearance between the knife and the anvil.
If there is not enough clearance, the knife edge may
touch  the  anvil  through  deflection  when  cutting
heavy  branches  and  damage  the  sharp  edge.  Too
much  clearance  will  allow  small  twigs  and  fibrous
materials to be dragged through without being cut.

To adjust the gap between the knives and the anvil,
first  loosen  the  locking  nuts  from  the  adjustment
bolts  on  the  anvil  mounting  plate  using  a  16  mm
spanner. Now tighten or loosen the two adjustment
bolts.  Tightening  these  bolts  will  cause  the  anvil
mounting  plate  to  slide  further  along  the  slotted
holes.  Ensure  you  tighten  the  two  bolts  evenly  to
avoid setting the anvil on an angle.

Once the correct anvil position has been set, ensure
the locking nuts on the adjustment bolts are
tightened. Additionally, ensure the clamping nuts
are torqued to 44 Nm.

Remove the rotor pin and turn the rotor slowly by
hand to check that it turns freely.

Close and secure the outlet chute.

WARNING!

Every time the knife clamping bolts are torqued up to 190 Nm and loosened off again, the life of the bolts is

reduced. The knife clamping bolts must be replaced at most after every six sharpens. Contact Hansa for replacement
bolts (m16x50 countersunk bolts of grade 12.9 or higher). Use only genuine Hansa bolts.

5

6

7

Locking nuts

Rotor disk

Clamping bolts

Knife

Countersink

clamping bolts

Adjustment bolts

Anvil

Rotor

disc

Knife

3 mm

clearance

Bearing

Top view: Knife and anvil set-up

Spring washers

«
...
12
13
14
15
16
...
»

Содержание C40





























Отзывы:

Нет отзывов