5
4
. Overview for HT60
. Overview for Screen
HT-60
· LCD
· Clear / Power
· Addition /
Subtraction
· Functions / Units
-Area
-Volume
-Indirect Measure
I, II, III
-Stake Out Setup
· Measure
· Measurement Records
· Reference / Bluetooth
· Laser Emitted Window
· Laser Receiving Window
1. Measuring Reference
2. Measuring Function
3. Memories
4. Laser Indicator
5. Add and Subtract
6. Maxmum Display
7. Indirect Measuring
8. Minimum Display
9. Stakes Direction Indicator
10. Main Screen and Units
11. Countdown Measuring
12. Bluetooth Indicator
13. Battery Status
14. Sub-Screen and Units
1
4
5
6
7
9
10
2
3
11
12
13
14
8
. Battery Installation & Power Status
1. This unit is powered by 2 x AAA Batteries.
2. Remove battery lid and observing correct polarity before install batteries.
3. Battery level is showed on screen with batty icon on screen .
4. When the icon appears, there are approximately 1000 times to measure.
5. Replace batteries when low battery icon flash on screen.
6. To change new batteries, when install new batteries, then close back lid.
1. To make summary or difference between two measurements is easy
2. Finish your first measure, than click to save as addend or hold to save as Minuend.
3. Take the second measurement, than click to add from addend or hold to subtract minuend.
. Measuring Functions
Area Measurement
1. Click to enable Area measurement.
2. Laser will be activated when entering area measurement mode.
3. Follow the instructions on main screen to measure WIDTH and LENGTH.
4. After finish all the instructions, the result [AREA] will be showed on screen.
2. Volume Measurement
1. Click twice to enable Volume measurement.
2. Laser will be activated when entering volume measurement mode.
3. Follow the instructions on main screen to measure WIDTH, LENGTH and HEIGHT.
4. After finish all the instructions, the result [VOLUME] will be showed on screen.
. Measurement Addition & Subtraction
meter
Length
Area
Volume
m
m
²
m
³
ft
ft
²
ft
³
in
ft
²
ft
³
0’0”1/32
ft
²
ft
³
1/32in
ft
²
ft
³
1/16in
ft
²
ft
³
1/8in
ft
²
ft
³
10/33
P
m
³
feet inch
inch
inch
inch
尺
0’0”1/32
. Unit Setting
1. There are 8 units inside the laser distance meter.
2. Click and hold to select preferred unit.
3. Unit Switch Reference
Single Measurement Mode
1. Move the laser dot onto the target.
2. Keep your position stable and click .
3. The measurement will be displayed on LCD Screen and laser will be turn off.
4. Click again to enable the laser dot for next measurement.
Continuous Measurement Mode
1. Continuous Measurement is also called tracking measurement and is recommend to use for seeking
proper distance.
2. Move the laser dot onto the target.
3. Keep your position stable and tap and hold , the laser distance meter will enter continuous
measurement mode.
4. Move the device back and forward to proper distance.
5. Click to pause the measurement.
6. Click again to leave the continuously measurement mode.
. Switch On and Off
1. Be sure to check battery status before start.
2. Click the or to turn on the device.
3. Device will process the initial procedure and get ready to measure by turn on the laser dot.
4. Tap and hold for 2 seconds to turn off.
5. The device will turn off automatically after 180 seconds.
. Distance Measurement
. Measurement Reference
1. There are two reference positions for measurement .
They are back of the unit, front of the unit, tripod thread and the spike
2. Click to select the proper position.
3. Indirectly Height I, II & III Measurement (base on Pythagorean)
1. Click thrice, four and five times to enable Indirectly Measurement.
2. Laser will be activated when entering indirectly measurement mode.
3. Follow the instructions on main screen to measure the LENGTH OF HYPOTENUSE(S) and BASE.
4. After finish all the instructions, the result [HEIGHT] will be showed on screen.
Indirect
Measure I
Indirect
Measure II
Indirect
Measure III
. iM
²
app & Bluetooth Setup
For the model supported Bluetooth could connected with phones support BLE4.0,
For Bluetooth version on your phone, please contact with your phone manufacturer.
We currently offer Measurement Kit on iTune and Play Store.
1. To turn on Bluetooth in pairing mode, press and hold .
2. The Bluetooth icon will keep flashing during paring.
3. Select proper device in the Connection Manager of APP
4. After connected with a beep sound the icon will stop flashing.
Pairing
Connected
. Store Measurement to Memory and Lookup
1. When you want to add the measurements on the screen, press to add to memory.
You could find the location in memory on the top of screen.
2. To lookup stored measurements, press and hold to enter the lookup mode.
3. Press to move the index up and hold to move index down.
4. To clear all stored measurements, press and hold again in lookup mode to clear all memory.
