background image

 

4

 

IMPORTANT SAFETY INFORMATION ABOUT   

PROPANE (LP) GAS 

A self contained LP-gas cylinder for use with this appliance must have a 
capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD 
(overfill protection device).

 

See Figure 1. 

 
The LP-gas supply cylinder to be used must be constructed and marked in 
accordance with the specification for LP-gas cylinders of the U.S. Department 
of Transportation (DOT) or the National Standard of Canada, 

CAN/CSA-B339, 

Cylinder, Sphere and Tubes for the Transportation of Dangerous Goods

 

The cylinder supply system must be arranged for vapor withdrawal. 

 

The cylinder used must include a collar to protect the cylinder valve. 

 

This appliance shall be used only outdoors in a well-ventilated space and 
shall not be used in a building, garage or any other enclosed space. 

 

When this appliance is not is use, the gas must be turned off at the supply 
cylinder. 

  Storage of this appliance indoors is permissible only if the cylinder is 

disconnected and removed from the appliance. 

  Cylinders must be stored outdoors in a well-ventilated area out of the 

reach of children. Disconnected cylinders must have threaded valve plugs 
tightly installed and must not be stored in a building, garage or any other 
enclosed areas. 

CSA (Canadian Standards Association) certified to ANSI Z21.97•CSA 2.41-2012 
“Outdoor Decorative Gas Appliances”

     

 

Figure 1 

 

SPECIFICATIONS 

INPUT 

40,000 Btu/hr 

30,000 Btu/hr Low fire 

Propane Regulator Pressure 

11 inches water column 

 

Clearances to combustible 
surfaces 

Sides      24in./61cm 

Top: 72 in. / 183 cm 

Содержание TRADTILE2PCFP-RED




















Отзывы: