FOOT CAP
NOTE: MAKE SURE ARROWS
FROM BOTH THE "U" BAR
AND ROCKER ASSEMBLY
ARE POINTING IN THE
SAME DIRECTION!
HEX WRENCH-1
HW0008
1
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
HEX WRENCH-2
HW0007
1
SF0F2115B
QTY
PARTS LIST
DESCRIPTION
ORDER PART #
FOOT CAP
FACTORY ASSEMBLY
FC0031
AAF06001
BOLT COVER
HW0028
8
QTY
SWIVEL BASE &
ROCKER
ASSEMBLY
5/16" X 40 MM
BOLT
HW0003
5/16" NUT
HW0015
"U" METAL
PLATE
CHAIR FRAME
PARTS LIST
DESCRIPTION
ORDER PART #
2
4
4
4
1
1
HW0295
HW0618
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
A
B
C
D
E
F
G
ROCKER PLATE
FACTORY ASSEMBLY
B
Ø
8.0 X 2.3 MM
SPRING WASHER
COVER
FACTORY ASSEMBLY
G0161
COVER
A
SEAT DESIGNS MAY
VARY BUT THE ASSEMBLY
IS THE SAME
Figure 1
Figure 2
ROCKER PLATE
E
G
C
D
F
"U" BAR
ROCKER
ASSEMBLY
"U" BAR
G
Step 1:
Do not attempt assembly if any parts are missing or damaged.
Step 2:
Step 3: Important: We recommend 2 people work together to assemble the chair.
If chair frame has
been properly positioned on the rocker assembly, all arrows on the "U" bar and rocker
assembly will be pointing in the same direction.
Step 4: Critical Step: The "U" metal plates must be installed in the proper location.
Hand
tighten nuts 3-4 revolutions only.
CAUTION: Failure to place "U" metal plates under the rocker plates and above the
"U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the
structure of the rocker plates and the "U" bar. Damage due to over tightening of bolts
or improper assembly could cause injury and may void your warranty.
Step 5:
Ensure the bolts are FULLY
tightened.
Step 6:
Identify all parts packed in the carton against the parts list. Remove all protective materials.
Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are
unsure as how to proceed with the assembly, call our Customer Service Center at
1-800-416-3511.
Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker
assembly is positioned all the way into the base. It may have shifted or vibrated out during
shipment.
Note the
arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the
rocker plate. Point the open end of the horseshoe away from you. The arrows on the rocker
assembly should be pointing towards you. Set the chair frame on the rocker assembly with
front of the seat facing you and the arrows on the "U" bar pointing towards you as shown
in
. This is very important for a safe, balanced rocking motion.
Insert the "U" metal plate, so that the "U" bar and rocker plate
are between both sides of the "U" metal plate. Make sure that the holes in the "U" metal
plate are completely aligned with the holes in the "U" bar as shown in
. Guide the
bolts through the holes on the top side of the "U" metal plate, through the holes in the
"U" bar portion of the chair, through the holes in the rocker plate and then, most importantly,
through the holes in the bottom side of the "U" metal plate. It is very important that the
holes in the bottom portion of the "U" metal plate be placed directly beneath the holes in the
rocker plate. Add a spring washer and a nut to each bolt as shown in
.
Repeat the same procedure on the other side.
Tighten all nuts and bolts with the hex wrenches provided.
Remove arrow labels from "U" bar and rocker assembly. Cover bolts with
bolt covers.
Your chair should be ready for use. If your chair is not rocking properly, double-check your
assembly procedure, especially Step 3. If the chair rocks too far forward to or is difficult to
rock backwards, you have probably installed the seat frame backwards on the rocker
assembly. If you need further assistance, please call our Customer Service Center
at 1-800-416-3511.
Figure 1
Figure 1
Figure 2
Read this
step and carefully examine.
IMPORTANT NOTE: Damage to frames or spring plates resulting from not FULLY
tightening the bolts, is not covered under warranty. Please read all instructions carefully
before assembly. If you have any questions regarding your assembly, call our Customer
Service Center at 1-800-416-3511.
