background image

4

SAFETY INFORMATION

 DANGER

 

• CARBON MONOXIDE HAZARD

• This heater is a combustion appliance. All 

combustion appliances produce carbon monoxide 

(CO) during the combustion process. This product is 

designed to produce extremely minute, non-hazardous

amounts of CO if used and maintained in accordance 

with all warnings and instructions. Do not block air 

flow into or out of the heater.

• Carbon Monoxide (CO) poisoning produces flu-like

symptoms, watery eyes, headaches, dizziness, fatigue

and possibly death. You can't see it and you can't 

smell it. It's an invisible killer. If these symptoms are 

present during operation of this product get fresh air 

immediately!

• For outdoor use only.

• Never use inside house, or other unventilated or

enclosed areas.

• This heater consumes air (oxygen). Do not use in

unventilated or enclosed areas to avoid endangering

your life.

 WARNING

 

 DANGER

 

• EXPLOSION - FIRE HAZARD

• Keep solid combustibles, such as building materials,

paper or cardboard, a safe distance away from the 

heater as recommended by the instructions.

• Provide adequate clearances around air openings

into the combustion chamber.

• Never use the heater in spaces that do or may 

contain volatile or airborne combustibles, or products

such as gasoline, solvents, paint thinner, dust particles

or unknown chemicals.

• During operation, this product can be a source of

ignition. Keep heater area clear and free from 

combustible materials, gasoline, paint thinner, cleaning

solvents and other flammable vapors and liquids. Do 

not use heater in areas with high dust content. 

Minimum heater clearances from combustible 

materials: three (3) feet from the sides & two (2) feet

from the top.

We cannot foresee every use which may be made of 

our heaters.

Check with your local fire safety authority if you have

questions about heater use.

Other standards govern the use of fuel gases and heat

producing products for specific uses. Your local 

authorities can advise you about these.

If no local codes exist, follow National Fuel Gas Code,

ANS Z223.1. In Canada, installation must conform to

local codes. If no local codes exist, follow the current 

National standards of CANADA CAN/CGA-B 149.2.

 WARNING

 

Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

An LP-cylinder not connected for use shall not be 

stored in the vicinity of this or any other appliance.

 WARNING

 

Improper installation, adjustment, alteration, service or 

maintenance can cause property damage, injury or 

death. Read the installation, operation and 

maintenance instructions thoroughly before installing

or servicing this equipment.

 DANGER

 

• EXPLOSION - FIRE HAZARD

• Never store propane near high heat, open flames, 

direct sunlight, other ignition sources or 

where temperatures exceed 120 degrees F (49°C).

• Propane vapors are heavier than air and can 

accumulate in low places. If you smell gas, leave the

area immediately.

• Never install or remove propane cylinder while heater

is lighted, near flame, other ignition sources

or while heater is hot to touch.

• This heater is red hot during use and can ignite

flammables too close to the burner. Keep flammables

at least 3 feet from sides & 2 feet from top. Keep 

gasoline and other flammable liquids and vapors well 

away from heater.

• Store the propane cylinder outdoors in a well ventilated

space out of reach of children. Never store the propane 

cylinder in an enclosed area (house, garage, etc.). If 

heater is to be stored indoors, disconnect the propane 

cylinder for outdoor storage.

Содержание 9710203
















Отзывы: