background image

22

Note: The reading of the first point could be skipped for FNU and NTU modes by pressing “Skip” 
functional key. In this case, the 0.00 value will be used for calibration.

• Place the cuvette for first calibration point:

  • <0.1 FNU (NTU) calibration cuvette for all modes 

except FAU mode.

  • 15 NTU formazin prepared standard for FAU mode.
Note: For the FAU mode, if necessary, press UP or DOWN 
key to edit the calibration point value to match the exact 
value of the standard. 
• Close the lid and press “Read” functional key. The 
display will show the value blinking and the light icon during measurement.
Note: If the Average mode was previously selected, the measurement in calibration mode will be 
done using the average.
• At the end of the measurement, the second proposed calibration point is displayed.

SECOND POINT CALIBRATION

• Remove the first calibration cuvette.

• Place the cuvette for second calibration point:

  • 15 NTU (FNU) calibration cuvette for NTU 

ratiometric mode.

  • 15 NTU formazin prepared standard for NTU 

non‑rating and FNU modes.

  • 100 NTU formazin prepared standard for FAU 

mode.

Note: If necessary, press UP or DOWN key to edit 

each calibration point value to match the exact 

value of the standard as measured with a reference 

turbidimeter.

• Close the lid and press “Read” functional key. The display will show the value blinking and the  

light icon during measurement.
• At the end of the measurement, the third proposed calibration point is displayed.

LOG

Содержание HI88713-01

































Отзывы: