Hanna Instruments HI 96721 Скачать руководство пользователя страница 4

4

GENERAL DESCRIPTION

ABBREVIATIONS

The 

HI 96721 

is an auto diagnostic portable microprocessor meter that benefits from Hanna’s

years of experience as a manufacturer of analytical instruments. It has the advanced optical
system based on a special tungsten lamp and a narrow band interference filter that allows most
accurate and repeatable readings. All instruments are factory calibrated and the electronic and
optical design minimizes the need of frequent calibration.
With the powerful CAL CHECK

TM

 

validation

 function, you are able to validate good performance

of your instrument at any time. The validation procedure is extremely user friendly. Just use the
exclusive HANNA ready-made, NIST traceable standards to verify the performance of the
instrument and recalibrate if necessary.
All instruments are splash waterproof and the lamp and filter units are protected from dust or dirt
by a transparent cup. This makes the instruments fulfill field applications. Display messages aid
the user in routine operation. The meter has an auto-shut off feature that will turn off the
instrument  after 10 minutes of non use in 

measurement mode or after 1 hour if left in  calibration mode.

The meter uses an exclusive positive-locking system to ensure that the cuvette is in the same
position every time it is placed into the measurement cell. It is designed to fit a cuvette with a
larger neck making it easier to add both sample and reagents. The cuvette is made from special
optical glass to obtain best results.
The 

HI 96721

 meter measures total iron (Fe) content in water samples in the 0.00 to 5.00 mg/L

(ppm) range. The method is an adaptation of the USEPA Method 315B for natural and treated
waters, and Standard Method 3500-Fe B for water and wastewater.
The reagent contains both a reducing and a complexing agent: the first converts all but very most
resistant forms of iron present in the sample to the ferrous (Fe

2+

) or soluble state; the second

reacts with the ferrous iron to form the characteristic orange-colored complex.
The reagent is in

 

powder form and is supplied in packets. The amount of reagent is precisely

dosed to ensure the maximum repeatability.

degree Celsius
US Environmental Protection Agency
degree Fahrenheit
milligrams per liter. mg/L is equivalent to ppm (parts per million)
milliliter
millivolts

°C

:

EPA

:

°F

:

mg/L

:

mL

:

   

mV

:

Содержание HI 96721

























Отзывы: