manualshive.com logo in svg

Hanna Instruments C 214, Инструкция по эксплуатации, Страница: 26 / 40

Поделиться
Скачать
Hanna Instruments C 214 Скачать руководство пользователя страница 26

26

• Mark the vial with a pencil on the

white band to place an orientation
sign. Use this sign to insert the test
vial always in the same position into
the holder.

•

Place the vial into the holder and
push it completely down.

•

Press ZERO and “SIP” will blink on the display.

•

Wait for a few seconds and the
display will show “-0.0-”. Now the
meter is zeroed and ready for
measurement.

•

Remove the vial.

•

Remove the cap and add 4 drops of
HI 93764-0 Nessler Reagent.

• Replace the cap tightly and mix by

inverting the vial a couples of times.
This is the sample.

•

Place the vial into the holder and
push it completely down. Ensure that
the vial orientation respect to the
holder is the same as the blank.

• Press TIMER and the display will show the countdown prior to the

measurement. Alternatively, wait for 3 minutes and 30 seconds
and press READ DIRECT. In both cases "SIP" will blink during
measurement.

Ammonia HR

55

COD HR

• Select the program number corresponding to Oxygen Demand,

Chemical HR (COD) on the secondary LCD by pressing PROGRAM

t

 and 

s

.

•

Place the blank vial into the holder
and push it completely down.

•

Press ZERO and "SIP" will blink on the display.

•

Wait for a few seconds and the
display will show “-0.0-”. Now the
meter is zeroed and ready for
measurement.

•

Remove the blank vial.

•

Place the sample vial into the holder
and push it completely down.

• Press READ DIRECT and "SIP" will blink during measurement.

• Multiply the reading on the Liquid Crystal Display by 10 to

obtain the concentration in 

mg/L of oxygen demand

.

INTERFERENCES

Interference may be caused by:
Chlorides (Cl

-

): above 20000 mg/L.

Samples with higher chloride concentration should be
diluted.

Содержание C 214









































Отзывы:

Нет отзывов