HANKISON SPXFLOW HSHD Series, Инструкция по эксплуатации

Страница: 3 / 32

1
1.0 General Safety Information
This equipment is designed and built with safety as a prime
consideration; industry-accepted safety factors have been
used in the design. Each dryer is checked at the factory for
safety and operation. All pressure vessels which fall under
the scope of ASME Section VIII, are hydrostatically tested in
accordance with the latest addenda.
WARNING – The following safety rules must be observed
to ensure safe dryer operation. Failure to follow these
rules may void the warranty or result in dryer damage
or personal injury.
1. Never install or try to repair any dryer that has been
damaged in shipment. See the Receiving and Inspection
instructions in this manual for appropriate action.
2. This equipment is a pressure-containing device. Never
operate the dryer at pressures or temperatures above
the maximum conditions shown on the data plate.
Never dismantle or work on any component of the dryer
or compressed air system under pressure. Vent internal
air pressure to the atmosphere before servicing.
3. This equipment requires electricity to operate. Install
equipment in compliance with national and local electrical
codes. Standard equipment is not intended for installation
in hazardous environments.
Never perform electrical service on the dryer unless the
main power supply has been disconnected. Parts of the
control circuit may remain energized when the power
switch is turned off.
4. Air treated by this equipment may not be suitable for
breathing without further purification. Refer to OSHA
standard 1910.134 for the requirements for breathing
quality air.
5. Use only genuine replacement parts from the manufac-
turer. The manufacturer bears no responsibility for hazards
caused by the use of unauthorized parts.
Safety instructions in this manual are boldfaced for emphasis.
The signal words
DANGER
,
WARNING
and
CAUTION
are used
to indicate hazard seriousness levels as follows:
DANGER – Immediate hazard which will result in severe injury
or death.
WARNING – Hazard or unsafe practice which could result in
severe injury or death.
CAUTION – Hazard or unsafe practice which could result in
minor injury or in product or property damage.
The dryer data plate contains critical safety and identification
information. If the data plate is missing or defaced, immedi-
ately contact your local distributor for a replacement.
2.0 Receiving, Storing, and Moving
2.1 Receiving and Inspection
This shipment has been thoroughly checked, packed and
inspected before leaving our plant. It was received in good
condition by the carrier and was so acknowledged.
Immediately upon receipt, thoroughly inspect for visible loss or
damage that may have occurred during shipping. If this ship-
ment shows evidence of loss or damage at time of delivery to
you, insist that a notation of this loss or damage be made on
the delivery receipt by the carrier’s agent. Otherwise no claim
can be enforced against the carrier.
Also check for concealed loss or damage. When a shipment has
been delivered to you in apparent good order, but concealed
damage is found upon unpacking, notify the carrier imme-
diately and insist on his agent inspecting the shipment. The
carrier will not consider any claim for loss or damage unless an
inspection has been made. If you give the carrier a clear receipt
for goods that have been damaged or lost in transit, you do
so at your own risk and expense. Concealed damage claims
are not our responsibility as our terms are F.O.B. point of ship-
ment. Shipping damage is not covered by the dryer warranty.
2.2 Storing
Store the dryer indoors to prevent damage to any electrical
or mechanical components. All packaging material should be
left in place until the dryer is in position.
The storage temperature should be between 32°F (0°C) and
131°F (55°C). Frost or higher temperature can cause damage.
Contact the manufacturer for long term storage/commission-
ing periods greater than 6 months.
2.3 Handling
CAUTION – Never lift the dryer by attaching hooks or
slings to the compressed air inlet or air outlet connec-
tions. Severe structural damage could occur.
IMPORTANT:
Allow handling only by personnel trained in the
safe movement of loads.