Hangar 9 PT-19 CL Скачать руководство пользователя страница 20

20

Hangar 9 PT-19 CL Assembly Manual

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot 

provide warranty support or repair. Once assembly, setup 

or use of the Product has been started, you must contact 

Horizon directly. This will enable Horizon to better answer 

your questions and service you in the event that you may 

need any assistance. For questions or assistance, please 

direct your email to productsupport@horizonhobby.

com, or call 877.504.0233 toll free to speak to a service 

technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please 

call for a Return Merchandise Authorization (RMA). Pack 

the Product securely using a shipping carton. Please note 

that original boxes may be included, but are not designed 

to withstand the rigors of shipping without additional 

protection. Ship via a carrier that provides tracking and 

insurance for lost or damaged parcels, as 

Horizon is not 

responsible for merchandise until it arrives and is 
accepted at our facility

. A Service Repair Request is 

available at www.horizonhobby.com on the “Support” tab. 

If you do not have internet access, please include a letter 

with your complete name, street address, email address 

and phone number where you can be reached during 

business days, your RMA number, a list of the included 

items, method of payment for any non-warranty expenses 

and a brief summary of the problem. Your original sales 

receipt must also be included for warranty consideration. 

Be sure your name, address, and RMA number are clearly 

written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include 
your original sales receipt

 verifying the proof-of-

purchase date. Provided warranty conditions have been 

met, your Product will be repaired or replaced free of 

charge. Repair or replacement decisions are at the sole 

discretion of Horizon Hobby.

Non-Warranty Repairs

Should your repair not be covered by warranty 
the repair will be completed and payment will 
be required without notification or estimate of 
the expense unless the expense exceeds 50% of 
the retail purchase cost.

 By submitting the item for 

repair you are agreeing to payment of the repair without 

notification. Repair estimates are available upon request. 

You must include this request with your repair. Non-

warranty repair estimates will be billed a minimum of 

½ hour of labor. In addition you will be billed for return 

freight. Please advise us of your preferred method of 

payment. Horizon accepts money orders and cashiers 

checks, as well as Visa, MasterCard, American Express, 

and Discover cards.

If you choose to pay by credit card, please include your 

credit card number and expiration date. Any repair left 

unpaid or unclaimed after 90 days will be considered 

abandoned and will be disposed of accordingly. 

Please 

note: non-warranty repair is only available on 
electronics and model engines.

united States:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Service Center 

4105 Fieldstone Road 

Champaign, Illinois 61822

All other Products requiring warranty inspection or repair 

should be shipped to the following address:

Horizon Product Support 

4105 Fieldstone Road 

Champaign, Illinois 61822

Please call 877-504-0233 or e-mail us at  

[email protected] with any questions or 

concerns regarding this product or warranty.

united kingdom:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Hobby UK 

Units 1-4 Ployters Rd 

Staple Tye 

Harlow, Essex 

CM18 7NS 

United Kingdom

Please call +44 (0) 1279 641 097 or e-mail us at  

[email protected] with any questions or concerns 

regarding this product or warranty.

Germany:

Electronics and engines requiring inspection or repair 

should be shipped to the following address:

Horizon Technischer Service 

Hamburger Strasse 10 

25335 Elmshorn 

Germany

Please call +49 4121 46199 66 or e-mail us at  

[email protected] with any questions or concerns 

regarding this product or warranty.

Содержание PT-19 CL

























Отзывы: