manualshive.com logo in svg

Hangar 9 40-Size Floats, Инструкция по сборке, Страница: 9 / 16

Поделиться
Скачать
Hangar 9 40-Size Floats Скачать руководство пользователя страница 9

9

Required Parts

• Assembled fuselage 

• Float (right and left)

• Strut mount (4) 

• Rudder

• Pushrod wire 

• Clevis

• Steering arm 

• Servo hatch

• Water rudder mount
• 5/3-inch wheel collar w/setscrew (4)
• 3mm x 8mm machine screw ()
• mm x 10mm sheet metal screw (4)
• 4-40 x 1/-inch machine screw (0)
• Pushrod connector w/backplate

Required Tools and Adhesives

• Side cutters 

•Phillips screwdriver

• Hex wrench: 1 .5mm 

• Threadlock

• Servo w/hardware 

• Clear silicone

• Y-harness

 

Step 1

Attach the strut mounts to the top of the left and right 

floats using four 4-40 x 1/-inch machine screws for  

each strut mount .

Note

: Always use threadlock on 

metal-to-metal fasteners to prevent 

them from vibrating loose .

 

Step 2

Install the rudder servo into the right float using the 

hardware provided with the servo .

 

Step 3

Attach the water rudder mount to the rear of the right float 

using four 4-40 x 1/-inch machine screws . Slide the 

pushrod wire into the pushrod tube threaded end first .

 

Step 4

Thread a clevis onto the pushrod wire . Use side cutters to 

remove any excess arms from the servo horn . Attach the 

clevis to the servo arm and secure the arm to the servo .

Float Installation

Содержание 40-Size Floats

















Отзывы:

Нет отзывов