background image

(+)

30 

AMP

VIP 3000 POWER JACK OWNER'S INSTRUCTIONS 

  P/N 30826(WHITE) OR P/N 31696, 31837 (BLACK )

GENERAL SAFETY:

Read and understand the Jack installation instructions.  Always block trailer wheel when using 

the jack. Remove jewelry (watches, rings, etc.) 

30 amp slow blow fuse

VIP Jack

travel trailer

battery

Connect the lead-wire directly to the positive (+) lead

of the travel trailer's battery using a twelve (12) gage wire. 

Be sure the connection is a good one.  

THE 30 AMP SLO-BLO FUSE MUST BE INSTALLED

AS SHOWN. 

INSTALLATION:

                                                              

 

 IMPORTANT NOTICE:

If it is necessary to change the position of the powerhead relative to the post and flange (in order to 

provide clearance between powerhead and LP gas bottle or LP gas cover, or more clearance between

the lift gate and the powerhead) loosen set screws and rotate head without lifting off coupling.  Retighten

set screws when head is in desired position. 

H&H ENGINEERING

DIVISION OF BARKER MFG. CO.

730 E. MICHIGAN AVE. / P.O. BOX 460 

BATTLE CREEK MI 49016 / (269) 965-2371

PAGE: 

DATE:

FORM #:

REV. LETTER:

ECN#:

APPROVED: 

1 OF 4 21 APR 08 30842

E

13855

BEFORE INSTALLATION:

Raise your travel trailer's front end and place blocks or stabalizing jacks under the front "A" frame. 

Lower the trailer until it rests securely on stabilizing jacks or blocks.  Retract present jack and remove.

H&H Engineering VIP 3,000 Power Jack is designed to lift up to 3,000 pounds a full 18".  It's design

also includes a night light, a build in leveling device, attached foot plate, and an emergency crank handle.

An important part of owning and using VIP Jack is being sure it is properly installed and serviced.

Remove present

jack

"A" frame coupler

IMPORTANT

To insure a good

electrical ground an

internal tooth lock-

washer must be in 

place for this bolt.  

Make sure powdercoat

or paint is  removed from

"A" frame coupler under

washer and that tagged

hole is used.

Supplied by customer

© 

Copyright H&H Engineering 1989

Install Jack in hole and secure with 3 bolts & 3 internal tooth lockwashers

(bolt holes are threaded)

Attach the foot plate to VIP Jack with .50-20 bolt and .50" lockwasher

HIGH POWER

 

SERIES

 3000

Содержание VIP 3000

Страница 1: ...VE P O BOX 460 BATTLE CREEK MI 49016 269 965 2371 PAGE DATE FORM REV LETTER ECN APPROVED 1 OF 4 21 APR 08 30842 E 13855 BEFORE INSTALLATION Raise your travel trailer s front end and place blocks or stabalizing jacks under the front A frame Lower the trailer until it rests securely on stabilizing jacks or blocks Retract present jack and remove H H Engineering VIP 3 000 Power Jack is designed to lif...

Страница 2: ...le will cause serious injury or death REMEMBER TO KEEP HANDS AND FEET OUT FROM UNDER THE FOOT PLATE WHEN USING THE POWER JACK DOLLY WHEELS ARE NOT RECOMMENDED BREAKING THESE RULES WILL CAUSE SERIOUS INJURY OR DEATH WARNING 19989 Don t risk serious injury or death in a shearing or squeezing accident Keep body hands and feet away VIP 3000 POWER JACK OWNER S INSTRUCTIONS P N 30826 WHITE OR P N 31696 ...

Страница 3: ...ting surfaces If lubrication is needed use Mobilith 460 grease or equivalent PAGE DATE FORM REVISION LETTER ECN APPROVED 3 OF 4 21 APR 08 30842 E 13855 H H ENGINEERING DIVISION OF BARKER MFG CO 730 E MICHIGAN AVE P O BOX 460 BATTLE CREEK MI 49016 269 965 2371 Copyright H H Engineering 1989 SCHEMATIC WIRING DIAGRAM STRAP ATTACHMENT 1 Press strap 1 onto the stud 2 at the bottom of the cap 2 Press th...

Страница 4: ...OVER LABEL 13 30683 1 LOCK INDICATOR LABEL 14 16434 2 HOLE PLUG 15 623 1216 1 GROOVE PIN 16 619 0003 3 LOCKWASHER INTERNAL TOOTH 17 608 0006 3 SET SCREW 313 18 X 50 18 621 0004 2 DOWEL Ø 13 X 75 19 17808 1 WIRE CLAMP 20 736 0008 1 TOGGLE SWITCH 21 29880 1 CONNECTOR FUSE HOLDER ASSEMBLY 22 645 0024 1 BUSHING 23 618 1002 1 LOCKWASHER 50 24 600 0011 1 HEX BOLT 50 20 X 75 25 634 0028 2 RETAINING RING ...

Отзывы: