Hand Held Products IT4410 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 32

Hand Held Products IT4410 Скачать руководство пользователя страница 13

1 - 9

A

if Row Height >= 1.5 X,

F

otherwise.

{6} lists the

Data Safety Margin

. Because MicroPDF's error correction level is

fixed, this parameter is just the "Unused Error Correction" and always
between 0 and 100%.

{7} lists the

Edge Accuracy

measured in multiple scans through the Row

Address Patterns.

{8} lists the

Print Growth

measured within the Row Address Patterns.

2D Matrix

This section describes 2D PQA outputs for Aztec Code, Data Matrix, QR Code,
and MaxiCode.

Aztec Code

The Full Report from a typical scan looks like the following (line numbers have
been added in curly brackets):

{1} This is a representative Aztec Code symbol

{2} >>> PQA from HHP <<<

{3} AZTEC CODE: 3 layers (Compact) => 23x23 modules

{4} Data Field: 29 data & 22 chks in GF(256), 0 Erasures

& 0 Errors

{5} X roughly = 0.021"

{6} [A] < Core Symbol: 0 errors

{7} [A] < Data Safety Margin = 146%

{8} [A] < Horizontal Print Growth = +1% of X

{9} [A] < Vertical Print Growth = +1% of X

{1} is the

Encoded Message

.

{2} is the

Banner

heading.

{3} identifies the

Symbology

(AZTEC CODE) and lists the symbol's size and

format.

{4} lists the numbers of

Data and Check Words

, as well as the Error Correction

used.

{5} presents an approximate

X-dimension

.

«
...
11
12
13
14
15
...
»

Содержание IT4410

































Отзывы:

Нет отзывов