HAMPTON BAY H35-NG2 Скачать руководство пользователя страница 40

Hampton

®

 H35-2 Direct Vent Freestanding Gas Stove

39

COPY OF THE LIGHTING PLATE INSTRUCTIONS 

OPERATING INSTRUCTIONS

AUTOMATIC 

CONVECTION 

FAN OPERATION

The fan operates automatically - turn the knob at 
the top right rear corner to adjust to the desired 
speed. The fan will turn on as the stove comes 
up to operating temperature. After the unit has 
been turned off and the unit cooled to below a 
useful heat output range the fan will shut off 
automatically.

1) Push in gas control knob slightly and turn to “PILOT” position.
2) Push in control knob all the way and hold in untilthe pilot lights

up. Continue to hold the control knob in for about 20 seconds

after the pilot is lit. Release knob.

3) Push in gas control knob slightly and turn to "ON" position.

4) Turn ON the flame switch.

2) Wait five (5) minutes to clear out any gas. If you then smell gas

STOP! follow “B” in the safety information above on this label. If

you don’t smell gas, go to the next step.

3) Tu rn knob on gas control counterclockwise

to “PILOT”.

4) Push in control knob all the way and hold in. Immediately push

black button on spark igniter until pilot lights. Continue to hold the

control knob in for about 1/2 minute after the pilot is lit. Release

knob and it will pop back up. Pilot should remain lit. If it goes out,

repeat steps 3) and 4).

If knob does not pop up when released, stop and immediately call

your service technician or gas supplier.

If the pilot will not stay lit after several tries, turn the gas control

knob to “OFF” and call your service technician or gas supplier.

5) Tu rn gas control knob counterclockwise

to “ON”.

6) Use rocker switch to operate main burner.

DO NOT REMOVE THIS INSTRUCTION PLATE

FOR YOUR SAFETY READ BEFORE LIGHTING

A) This appliance has a pilot which must be lighted by hand, following the instructions below exactly.
B) BE FORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

-

Do not try to light any appliance

-

Do not touch any electric switch, do not use any phone in your building

-

Immediately call your gas supplier from a neighbors phone. Follow the gas supplier’s instructions.

-

If you cannot reach your gas supplier, call the fire department.

C) Us

try to

repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D) Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and

to replace any part of the control system and any gas control which has been under water.

E) Thisappliance needs fresh air for safe operation and must be installed so there are provisions adequate comb ventilation air.

918-474b

OFF

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,

or additional information consult a qualified installer, service agency or gas supplier.

LIGHTING INSTRUCTIONS

TO TURN OFF GAS APPLIANCE

THERMOPILE

ELEMENT

THERMO-

ELECTRIQUE

PILOT BURNER

VEILLEUSE

1/

NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1. (Australia: A S5601-2004, New Zealand: NZS 5261)

FOR UNITS NOT EQUIPPED WITH ELECTRIC SPARK:

. Keep burner

appliance.

STOP! Read the safety information above on this label.

FORALL PROPANE UNITS AND

UNITS EQUIPPED WITH ELECTRIC SPARK BOXES:

1) Push in gas control knob slightly and turn clockwise

to

“OFF”. Knob cannot be turned from “PILOT” to “OFF” unless

knob is pushed in slightly. Do not force.

1) Turn off the flame switch.

2) Push in the gas control knob slightly and turn clockwise

to “OFF”. Do not force.

3) Turn off all electric power to the appliance if service is to be performed.

You may shut off the pilot during prolonged non use periods to conserve fuel.

l

ADJUSTING FLAME 

HEIGHT

 
Your heater has an adjustable fl ame to tailor the 
look and heat output to your specifi c needs. It 
is adjusted by turning the fl ame adjustment dial 
on the gas control valve.

Turn clockwise to adjust the fl ame higher, coun-
terclockwise for a lower fl ame.

Содержание H35-NG2


















































Отзывы: