background image

4

REMEMBER

 to turn off the power. Follow the 

steps below to hang your fan properly.

NOTE:

 This ceiling fan is supplied with two types 

of hanging assemblies; the standard ceiling 
installation using the downrod with ball and socket 
mounting, and the "close-to-ceiling" mounting. 
The "close-to-ceiling" mounting is recommended 
in rooms with less than 8-foot ceilings or in areas 
where additional space is desired from the floor to 
the fan blades.

When using the standard downrod installation, the 
distance from the ceiling to the bottom of the fan 
blades will be approximately 12 inches. The 
"close-to-ceiling" installation reduces the distance 
from the ceiling to the bottom of the fan blades to 
approximately 9 inches.

Once you have decided which ceiling installation 
you will use, proceed with the following 
instructions. Where necessary, each section of the 
instructions will note the different procedures to 
follow for the two types of installation.

Hanging the Fan

Option 1:

Standard Ceiling Mounting

WARNING

FAILURE TO PROPERLY INSTALL COTTER PIN 

AS NOTED IN STEP 5 COULD RESULT IN FAN 

LOOSENING AND POSSIBLY FALLING.

Figure 7

Remove the
Canopy Ring

Figure 5

Loosen but 
do not remove

Remove

Figure 6

Remove the canopy ring from the canopy. 
(Figure 5).

1.

Remove the mounting bracket from the canopy 
by loosening the four screws on the top of the 
canopy. Remove the two non-slotted screws 
and loosen the slotted screws (Figure 6).

2.

Align the holes at the bottom of the downrod 
with the holes in the coupling on top of the 
motor housing (Figure 7). Carefully insert the 
clevis pin through the holes in the collar and 
downrod. Be careful not to jam the clevis pin 
against the wiring inside the downrod. Insert 
the cotter pin through the hole near the end of 
the clevis pin until it snaps into its locked 
position, as noted in the circle inset of Fig. 7.

Tighten two set screws on top of the fan motor 
firmly. (Figure 7)

5.

6.

Route wires exiting from the top of the fan 6. 
motor through the coupling cover and canopy 
ring. Make sure the slot openings are on top. 
Route the wires through the canopy and then 
through the ball/downrod assembly (Figure.   
7).

Loosen, but do not remove the 2 set screws on 
the collar on top of the motor housing.

3.

4.

Motor Wires

Ball/Downrod 
Assembly

Ceiling Canopy

Canopy Ring

Pin in Locked 
Positioon

Motor Collar

Coupling Cover

Tighten Screw 
Firmly

Cotter Pin

Clevis Pin

Содержание 164-352


















Отзывы: