background image

30

!

Bandsaw

N3700 e-classic / N3800 / N4400

9.4 Faults, causes and repairs

Fault

Cause and problem elimination

Machine does not start

Safety break switches are breaking the electric circuit

Ensure that the side doors are closed properly

Emergency stop switch engaged

Unlock the emergency stop switch

Squeaking noises when starting up

Insufficient tension (Drive belt)

Retensioning the drive belt

The cuts are not straight

Check sharpness and set of saw blade
Check the guide fence alignment

The saw blade is torn at the base of 

the individual teeth

Incorrect sharpness and constant overheating, or otherwise incorrect set of 

saw blade
Width of saw blade is too thick in relation to the diameter of the wheel
Defect or soiled wheel running surfaces
Incorrectly aligned wheels

 

✆ 

Felder

The saw blade is rupturing on the 

rear side

Feed rate or pressure is too high during cutting
Poor welded joint

 Saw blade replacement

The rear support roller of the saw blade guide is defective

The machine comes to a stillstand 

with the saw belt locked into the 

workpiece

Stop the motor and loosen the the brake. Enlarge the cutting gap with a 

wedge and remove the workpiece. Prior to switching the machine on again, 

check the condition of the saw belt and its position on the wheels

The saw belt is straying forwards 

and backwards

The belt is not aligned with the welded joints

 Saw blade replacement

The saw blade is slipping to the 

back at the beginning of the cut

The saw blade is not sharp enough or is unsuitable for the type of material to 

be cut, or the surface of the wheel is defective

 

Faults

Attention! The electrical diagrams supplied are only for the use of qualified electricians or the manu-

facturer’s authorized technical personnel. These diagrams do not authorize you in any way to change 

the electrical parts or logic functioning.

Note: The original spare parts that have been authorised for use are listed in a separate spare parts catalo-

gue, enclosed in the documentation package supplied with the machine.

10 Circuit diagrams / Spare parts

Содержание N3700 e-classic

































Отзывы: