Hammer INSPIRE SCS Cage, Руководство пользователя

Страница: 17 / 32

16
Select one of the Upper Cables. Position the Left Cable Column
Slider Assembly at a comfortable working height. Slide the
retainer “O” Ring up the cable about 3 inches from the cable
end for installation (this allows the cables to feed through their
routings easier). Remove one Jam Nut from the cable bolt and
insert the cable bolt, threaded end down, through the bracket
on the Cable Column Slider Assembly. Return the Jam Nut to
the cable bolt (below the bracket) to secure it on the Left Cable
Column Slider Assembly. Continue feeding the cable up around
Pulley #1, into and through the Left Top Beam, going out at
the rear. Make sure you route the cable to the correct side of all
cable guides and pins. Failure to route the cable properly will
result in damage to the cable. Now route the cable over Pulley
#3 and down through the Floating Pulley with Guide Bushing,
Pulley #4. Make sure the Guide Bushing is facing towards the
rear of the machine. Route the cable up over Pulley #5 and
Pulley #6 and down to the Weight Stack Top Pulley #7. Route
the cable up over Pulleys #8 and #9 and then down through the
second Floating Pulley #10. Complete the cable routing going
up over Pulley #11 at the rear of the Lat Attachment and forward
out through the Swivel Pulley Assembly at the front of the Lat
Attachment. Attach Cable End by placing one Plastic Ball on the
end of the cable, next slide the end of the cable into the slot of
the Cable “U” Bracket. Attach the Spring Clip to the “U” Bracket
using a M6 x 20 Button Head Bolt and M6 Flat Head Nut. Slide
the retainer “O” Ring tight against the Plastic Ball. Finally, install
Pulley #2 in the Top Beam per above detail
Vyberte si jeden z horn
í
ch kabel
ů
. Um
í
st
ě
te sestavu jezdce lev
é
-
ho sloupku kabelu do pohodln
é
pracovn
í
v
ýš
ky. Posu
ň
te dr
žá
k
„
O“ Zakrou
ž
kujte kabel asi 5 cm od konce kabelu (to umo
ž
ň
uje
kabel
ů
m snadn
ě
j
ší
veden
í
). Odstra
ň
te jednu pojistnou matici
ze
š
roubu kabelu a vlo
ž
te
š
roub, koncem se z
á
vitem dol
ů
, skrz
dr
žá
k na sestav ě . Vra ť te matici na
š
roub kabelu (pod dr
žá
kem),
abyste jej zajistili zp
ě
t na sestav
ě
. Pokra
č
ujte v nav
í
jen
í
lanka
kolem kladky #1, do lev
é
ho horn
í
ho nosn
í
ku a skrz n ě j, ve ď te
ven na zadn
í
čá
st. Ujist
ě
te se,
ž
e kabel vedete na spr
á
vnou
stranu v
š
ech kabelov
ý
ch vod
í
tek a kol
í
k ů . Nespr
á
vn
é
veden
í
kabelu bude m
í
t za n
á
sledek po
š
kozen
í
kabelu. Nyn
í
ve
ď
te
kabel p ř es kladku #3 a dol ů p ř es plovouc
í
kladku s vodic
í
m
pouzdrem, kladka #4. Ujist
ě
te se,
ž
e vodic
í
pouzdro sm
ěř
uje k
zadn
í
čá sti stroje. Ve ď te kabel nahoru p ř es kladku #5 a
kladku #6 a dol
ů
k horn
í
kladce z
á
sobn
í
ku z
á
va
ží
#7. Trasa
lanko nahoru p
ř
es kladky #8 a #9 a potom dol
ů
p
ř
es druhou
plovouc
í
kladku #10. Dokon
č
ete veden
í
kabel
ů
nahoru p ř es kladku #11 v zadn
í
čá sti n
á
stavce laty a dop ř edu
ven p ř es sestavu oto č n
é
kladky v p ř edn
í
čá sti n
á
stavce laty. P ř i-
pojte konec kabelu um
í
st ě n
í
m jedn
é
plastov
é
kuli č ky na konec
kabelu a pot
é
zasu ň te konec kabelu do otvoru v dr
žá
ku
„
U“
kabelu. P
ř
ipevn
ě
te pru
ž
inovou svorku k
„
U“ dr
žá
ku pomoc
í
š
roubu s knofl
í
kovou hlavou M6 x 20 a matice s plochou hlavou
M6. Nasu
ň
te
„
O“ krou
ž
ek t
ě
sn
ě
u plastov
é
kuli
č
ky. Nakonec na-
instalujte kladku #2 do horn
í
ho nosn
í
ku podle v
ýš
e uveden
é
ho
detailu.
Kladky 5 a 6
Konec kabelu
Kabel uvnit
ř tyče
Kladka 1
Kladka 3
Plovoucí kladka 10
Plovoucí kladka s
pr
ůchodkou
Kladka 4
Kladka 7
Horní kabel
Kladka
Šroub
Vložka
Matice