HAMAR LASER Dual Scan L-732 Скачать руководство пользователя страница 13

Страница: 13 / 37

The Precision Level Vials

Reading the Precision Level Vials

Secure the laser base to a metal surface by turning the locking

magnetic base ON. Once the laser is in position, power it on

and light the level vials (if necessary) using the LEVEL switch

located on the control panel. Use the adjustment knobs to bring

the bubbles to the center of both vials (see Figure 4).
When both the PITCH and ROLL vials are reading level, a

level beam can be scanned at 360 degrees with a .0003 in.

deviation per 10 ft.

Reading the L-740SP Split-Prism Level Vials

Once the laser unit is in position on the base, connect

power to the base power supply input jack and press the

red button to light the precision level vials. Use the

coarse

alignment micrometers to bring the bubbles to the

center of the vials.

When the bubbles are close to the center, use the

fine

adjustment micrometers to align the bubble halves to

each other in the viewing prism window (see Figure 5).

When both the long axis and short axis vials are reading

level, a level beam can be scanned at 360 degrees with a

.0003 in. deviation per 10 ft.

Calibrating the Level Vials

Note 1:

This procedure calibrates only one level vial at

a time and must be repeated for the other axis.

Note 2:

It is very important to warm up the laser for at

least 30 minutes before starting this procedure. It is also

very important to level both the Pitch and Roll axis level

vials during this procedure. Failure to do this makes it

nearly impossible to calibrate the levels.

The calibration procedure involves a series of steps to adjust the laser beam to be level to earth. Because

the leveling process is subject to so many variables, repeat the procedure to check for accuracy once the

initial readings are taken and adjustments are made. A typical sequence would be as follows:

•

Determine

the set point and set the first axis.

•

Use

the set point value to set the second axis.

•

Check both the first and second axes. Reset the levels if necessary.

•

If the levels are reset, make a final check to determine if the laser level error is acceptable.

Figure 4 –

Precision Level Vial entered (top) and off

center (bottom)

Figure 5 –

L-740SP Split-Prism Level Vial Assembly for L-

740 Series Lasers

Please Note!

Our level vials are designed to be calibrated by the customer. We cannot guarantee that the level

vials are calibrated when you receive the equipment because of movement during shipping. Please

follow the procedure below specific to the level vials on your laser.

Содержание Dual Scan L-732






































Результаты поиска

Содержание Dual Scan L-732

Отзывы:

Похожие инструкции для Dual Scan L-732

Бренды по названию

Популярные бренды

HAMAR LASER Dual Scan L-732, Руководство по эксплуатации

Результаты поиска

Содержание Dual Scan L-732

Отзывы:

Похожие инструкции для Dual Scan L-732

Бренды по названию

Популярные бренды