Hamamatsu Photonics C15550-20UP Скачать руководство пользователя страница 24

Страница: 24 / 72

qCMOS Camera C15550-20UP / C15550-20UP01 Instruction manual_Ver.1.3

9. OPERATIONS

9-1 OPERATING PRECAUTIONS

Be careful of the following when you operate the camera.

(1) Cooling method

Cooling of this equipment is done using a Peltier element.

With a Peltier element, when current is supplied, one surface is cooled, and the other surface is

heated. CMOS image sensor is positioned on the cooled side, and cooling is done by discharging

the heat from the heated surface.

The camera has two cooling methods, Air-cooling method and Water-cooling method.

The default of cooling method is Air-cooling. Cooling mode can be changed by software which is

called, “DCAM Configurator”. (refer to 9-5 “STARTUP DCAM CONFIGURATOR”).

Cooling method

Detail

Air-cooling method

(Forced air-cooled)

(Default)

The heated side of a peltier element is cooled by a fan inside the camera. When

the camera is turned on, the fan starts rotating and cooling is started.

Water-cooling method

Circulating water cooler (Optional) is used for cooling the heated side of a peltier

element. Cooling does not start just turning on the camera. Cooling water

circulation must be started before start operating the camera in water-cooling.

A fan inside the camera does not rotate.

•

See 8 “WATER COOLING” for instruction of water-cooling.

•

Do not switch to water-cooling method when water-cooling is unnecessary.

(2) Ambient temperature

The recommended ambient temperature for camera operation is 25 °C.

Both water-cooling or air-cooling are available as cooling method, CMOS image sensor cooling

temperature is more stable under water cooling operation.

(3) Protection circuit

This camera’s thermoelectric cooling device is protected by a thermal protection circuit.

If the internal

temperature of the camera becomes abnormally hot, the protection circuit operates

inform the user by a buzzer alarm (beep tone) and lighting the camera red LED light while

simultaneously cutting the current supply to the Peltier element. As soon as this protection is

implemented, turn off the power switch, unplug the AC supply. Then remove the cause of the

overheating.

(4) CoaXPress interface board

If you use an optional CoaXPress interface board, a message prompting update of the interface

board may be displayed. In this case, an update procedure manual will be displayed when you

click on the message. Update the interface board according to the procedure manual. (refer to 9-

6 "UPDATE PROCEDURE OF COAXPRESS INTERFACE BOARD”).

Содержание C15550-20UP









































































Результаты поиска

Содержание C15550-20UP

Отзывы:

Похожие инструкции для C15550-20UP

Бренды по названию

Популярные бренды

Hamamatsu Photonics C15550-20UP, Инструкция по эксплуатации

Результаты поиска

Содержание C15550-20UP

Отзывы:

Похожие инструкции для C15550-20UP

Бренды по названию

Популярные бренды