Hamamatsu Photonics C15440-20UP Скачать руководство пользователя

Страница: 62 / 70

qCMOS Camera C15550-20UP Instruction manual_Ver.1.0

12-2 INFORMATION ON COOLING WATER FOR THE CIRCULATING

WATER COOLER

•

Regarding handling cooling water and circulating water cooler, refer to instruction manual

attached to the circulating water cooler.

•

It is recommended to use soft water (except pure water) for cooling water.

•

Do not use hard water for cooling. It cause inside of cooling water circulating path to be

calcified or corroded and it result lower flow rate or water flow stop. When using hard water,

conduct a process to soften water before use it.

12-2-1 WHEN USING COOLING WATER OTHER THAN RECOMMENDED

Note

[Pure water]

•

Pure water is not appropriate for cooling water. There is possibility that pure water absorb

component of cooling water path and it may cause corrosion. In addition pure water is easy to be

polluted and cause impurity, sliminess or forming foreign substances. It cause lower flow rate or

water flow stop.

[Distilled water / Deionized water]

•

When using the camera inside clean room, it is possible to use distilled water or deionized water

by conducting periodical check. However notice it increases possibility of corrosion inside cooling

water path, lowering flow rate or water flow stop.

•

Monthly check : Check water impurity, non-existence of sliminess, foreign particle is not mixed

with water or not adhered inside water path and no unusual odor. If you find any of the issues,

exchange cooling water and clean cooling water path.

[Soft water from tap]

•

It is possible to use soft water from tap with conducting periodical change of cooling water and

checkup. However notice it increases possibility of corrosion inside cooling water path, lowering

flow rate or water flow stop.

•

Monthly check : Check water impurity, non-existence of sliminess, foreign particle is not mixed

with water or not adhered inside water path and no unusual odor. If you find any of the issues,

exchange cooling water and clean cooling water path.

•

Exchange cooling water every 3 months.

•

Clean cooling water path every 6 months.

[Bottled water]

•

One example of soft water which is commonly available is mineral water (Hardness less than 70).

Check hardness of water by referring product information of bottled water manufacturer.

Содержание C15440-20UP







































































Результаты поиска

Содержание C15440-20UP

Отзывы:

Похожие инструкции для C15440-20UP

Бренды по названию

Популярные бренды

Hamamatsu Photonics C15440-20UP, Инструкция по эксплуатации

Результаты поиска

Содержание C15440-20UP

Отзывы:

Похожие инструкции для C15440-20UP

Бренды по названию

Популярные бренды