3
2.3 Explanation of symbols used on the product label
Warning - risk of injury
Note the warning symbols in order to avoid injuries or damage to the device.
General warning symbol
Before commissioning, read the enclosed operating
instructions.
You must comply with the safety instructions at all times.
•
This device is not intended for use by children.
•
Avoid touching the intake opening with hands, clothing
or hair.
•
Unplug the device if it is not going to be used for a
prolonged period.
Children must be supervised when using the device.
Do not insert paper clips into the intake shaft.
Do not reach into the intake shaft.
Keep clothing away from the intake shaft.
Keep jewellery, e.g. necklaces, away from the intake shaft.
Keep hair away from the intake shaft.
Do not use any aerosol products on or near the device.
Insert no more than 5 sheets of paper at any one time into the
manual intake shaft (1).
Do not insert CDs/DVDs into the intake shaft (1/2).
Intake shaft for credit cards. Only insert one credit card at a
time into the intake shaft for credit cards.
PRESS TO LOAD
Press the paper guide flap (6) down.
= max.10 Sheet
First load the unstapled side of the paper into the automatic
intake shaft (2). Maximum 10 sheets stapled together.
Insert no more than 120 sheets of paper at any one time into
the automatic intake shaft (2).
Plastic cards must
not
be shredded in the automatic intake
shaft.
Do not insert paper clips into the automatic intake shaft.
2.4 Safety device
The device is equipped with a safety switch and can only be operated if the basket (7) is
correctly inserted into the device.
Warning
Any tampering with or modification of the safety features can result in serious injury
and is not permitted.
3. Installation / Setup
Warning
•
Only operate the product from a socket that has been approved for the device. The
socket must be installed close to the product and must be easily accessible.
•
Disconnect the product from the power supply using the On/Off switch – if this is not
available, unplug the power cord from the socket.
•
If using a multi-socket power strip, make sure that the total power consumption of
all connected devices does not exceed the power strip's maximum throughput rating.
•
If you will not be using the product for a prolonged period, disconnect it from
mains power.
Note
•
Set the product up on a level, horizontal and sufficiently stable surface.
•
Route all cables so that there is no risk of tripping.
•
Do not bend or crush the cable.
•
Protect the connecting cable from hot surfaces and sharp edges.
•
Connect the mains cable to a properly installed and easily accessible mains socket.
4. Operation
Note
•
Be aware that the thickness of paper increases when it is folded, leading to the
device's maximum page capacity being exceeded.
•
Always wait until one cutting operation is finished before starting the next one.
•
Do not use the device continuously for more than 60 minutes at a time.
•
Empty the container regularly in order avoid damaging the device.
4.1 Switching the device on
•
Move the main switch (10) to the "|" position.
•
Press the "ON/OFF" button (13).
•
The Ready status LED (16) lights up solid green.
•
The device is now ready for use.
4.2 Switching the device off
•
Press the "ON/OFF" button (13).
•
The Ready status LED (16) goes out.
•
Move the main switch (10) to the "O" position.
Note
If too much paper is fed in at the same time, the shredder stops automatically and ejects
the paper backwards. The Overload status LED (15) lights up and the Ready status LED
(16) starts flashing. This may have been caused by too much paper being stapled, paper
that is too thick, folded or not stacked neatly. Remove the excess paper and reduce the
number of sheets if necessary.
Содержание 00 50547
Страница 2: ......
Страница 3: ...8 4 7 10 5 9 1 6 2 3 14 9a 9a 9b 9b 11 15 12 16 13 ...
Страница 76: ...74 ...
Страница 77: ...75 ...