Page 5
98986C (Rev. M - 12/17)
HTHBHVR8-NF*1A, *2A, *3A HTHBHVR-NF*A, *2A HTHBHVR8*1A, *2A, *3A HTHBHVR*A, *2A
Fig. 4
Note: Screw the locknut hand tight to seal
Fig. 5
BOTTLE FILLER INSTALLATION
(FOR NON-FILTERED AND FILTERED HVR MODELS)
1)
Remove wall mounting plate
from Cooler. Install Wall Mounting Plate as per rough-in diagram (See rough-in on page 4).
NOTE:
Mounting plate
MUST
be supported securely. Add fixture support carrier if wall will not provide adequate support.
2)
Install water cooler onto wall bracket
and secure to wall. Connect drain and water inlet to cooler as required (See rough-in on page 4).
DO NOT
connect power to cooler at this time or turn water supply on.
3)
Remove HTHBHVR Bottle Filler
from carton. Remove 3/8” to 1/4” reducing union from end of waterline, (do not throw away it will be needed later). Lay Bottle Filler on water
cooler basin and cut insulation from tube even with bottom of unit, remove this insulation from the 3/8” tube, but do not discard. Feed the power cord and waterline through the
hole on top of water cooler. Feed the Reset Button wire from circuit board down through the hole in the basin.
NOTE:
To prevent scratching the basin place a towel or soft cloth over the entire basin when working above it.
4)
With the power cord,
waterline and reset button wires through the hole on top of water cooler place Bottle Filler on to mounting bracket on basin. (See Fig. 3). Make sure Bottle
Filler is installed properly on the basin gasket.
5)
Once Bottle Filler
is installed on basin mounting bracket, tighten the two screws (supplied) one on each side of the Bottle Filler. Install Top Cover on Bottle Filler (See Fig. 3) with
two mounting screws (supplied). Caution do not over tighten screws.
6)
Install remaining tube insulation to the waterline
from Bottle Filler. Connect Bottle Filler waterline inside of the water cooler by connecting the 3/8” waterline with the 3/8” to
1/4” union and short piece of poly tube that was previously installed to the tee at the evaporator outlet.
7)
For Filtered Model HTHBHVR coolers install filter cartridge:
Remove filter from carton. Remove protective cap and attach filter to filter head by firmly inserting into head and
rotating filter clockwise.
NOTE:
If the existing plumbing rough-in locations (Drain, Water In, Electric Supply) do not allow the filter to be mounted inside the cooler cabinet, the filter can be installed
horizontally below the unit. A retrofit kit is available to mount the filter beneath the cooler.
8)
Turn water supply on
and inspect for leaks. Fix all leaks before continuing.
9)
Once unit has been inspected
for leaks and if any leaks that are found are corrected, plug Bottle Filler and HTHBHVR unit into wall. Be sure to reinstall fuse to the circuit or
switch the circuit breaker back to the “ON” position.
10)
Once power is applied to Bottle Filler,
the GREEN LED light should illuminate showing good filter status along with the LCD Bottle Counter.
11)
Verify proper dispensing
by depressing the button at the top of the Bottle Filler and verify water dispenses. Note: the first initial dispenses might have air in line which may
cause a sputter. This will be eliminated once all air is purged from the line.14)
Once unit tests out
, install Lower Panel back on HTHBHVR water cooler. Unit is now ready for
use.
MOUNTING BRACKET
FOR FASTENING UNIT
TO WALL
TOP COVER
MOUNTING
SCREWS
Fig. 3
MOUNTING SCREWS
DO NOT REMOVE
MOUNTING SCREWS
DO NOT REMOVE
BOTTLE FILLER
WATER COOLER
NOTE: TRIM PLATES MUST
BE INSTALLED ON THE
INSIDE OF THE BOTTLE
FILLER SIDE PANEL SLOTS.
B
C
A
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A
B
C
