PAGE 11
4420BFFR_FTN _A LK4420BFFR_FTN_A
1000003686 (Rev. D - 03/20)
The following items are included with
the 4420BFFR Fountain
28467C
98901C
66346C
1000003814*
45476C
0000000325
45931C
98685C
66815C
66816C
97446C
75724C
97247C
98679C
98680C
98681C
1000003692
1000003693
98683C
98684C
40551C
98686C
1000003812*
1000003813*
28703C
28703C-LK
28091C-HT
1000005456
75565C
56092C
56123C
56307C
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
41
41a
41b
42
NS
NS
NS
NS
Basin
Kit - FR Push Button/Sleeve/Nuts
Tube-Drain
Cover - Round Plate
Tube - Drain
Kit - Drain Plug/Gasket
Plug - Outdoor Bottle Filler Drain
Kit - Hardware/Bolts/Nuts/Washers/Torx Screws
Tube - Drain
Tube - Drain (Arm Only)
Kit - VR Bubbler
Pinned Torx Screw - 1/4-20 x 3/4"
Kit - VR Torx Screws/Bit
Kit - Nozzle/Aerator/Gasket/Pin
Kit - Aerator/Key
Kit - Blank Bottle Filler Trim
Kit - LK4420BFFR Bottle Filler Trim
Kit - 4420BFFR Bottle Filler Trim
Kit - Plastic Drain
Kit - 90° Plastic Drain
Tailpipe - 1-1/4" X 6-7/8"
Kit - Bottle Filler Waterway
Panel - Access
Cover - Bottom
Blank Nameplate Insert (only)
LK4420BFFR Nameplate Insert (only)
4420BFFR Nameplate Insert (only)
Aesthetic Collar
Fitting - Double Male Connector
Poly Tubing - 1/4"
(Cut To Length) - To Bubbler
Poly Tubing - 1/8"
(Cut To Length) - To Actuator
Poly Tubing - 3/8"
(Cut to Length)
ITEM NO.
PART NO.
PARTS LIST
DESCRIPTION
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
1333 BUTTERFIELD RD, DOWNERS GROVE, ILLINOIS 60515
*select color option to complete part number
NS = Not Shown
*FINISH COLOR OPTIONS –
Choose color option to
complete your model number, add as suffix example:
4420BFFRK
EVG
Matte finish: Evergreen =
EVG
Gloss finish:
Beige =
BGE
Gray =
GRY
Terracotta =
TER
Black =
BLK
Orange =
ORN
White =
WHT
Blue =
BLU
Purple =
PUR
Yellow =
YLW
Brown =
BRN
Red =
RED
Vandal-Resistant
Bubbler Detail
FIG. 10
BASIN
28
TROUBLESHOOTING AND MAINTENANCE
Insufficient Bubbler Flow:
Check that the shut-off valve is wide open. Verify minimum 20 PSI supply pressure. Clean inlet strainer screen located in the valve
body. Clean rubber orifice in flow control located below frost line in bushing between barb fitting and valve.
No Flow:
Check for leaks in the air tubing going from the push button to the valve. Make sure the air tubing compression nut is hand tight. Disconnect air tube from
push button. Place finger over air outlet. Push button to test diaphragm. Tighten diaphragm cap screws. Replace diaphragm if necessary.
Continued Insufficient or Varied Height of Bubbler Flow:
•
Check for kinks in the tubing.
•
Remove the valve assembly from the PVC column by carefully pulling up on the strap and connecting tubing at the same time. Check stream height from the
bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, adjust the screw on the regulator (Item 13, Fig. 5, Page 7). Clockwise
adjustment will raise stream and counter-clockwise adjustment will lower stream. For best adjustment stream height should be approximately. 1-1/2" (38mm) above
the bubbler guard. Replace the valve into the PVC column. Make sure the supply hose coils into the bottom of the PVC column without any kinks and double check
that the valve is positioned fully at the bottom of the PVC column.
Continuous Bubbler Flow:
Insure that push button is not obstructed and springs back to normal position. Remove four screws which secure plastic diaphragm block
to valve body. Pull plastic and rubber diaphragm assembly out of valve body. Locate tiny hole in rubber diaphragm just under lip of plastic part. Clean debris from this
hole. Inspect valve seat for grooves. If valve seat was OK and diaphragm hole was free from debris, inspect rubber button located at center of floating steel disc in valve
diaphragm block assembly. If button is worn, turn disc over or replace it. If diaphragm and seats are in good condition, stretch spring slightly. Spring is located behind
floating stainless steel plate. Insure that air bleed port on valve plastic block assembly is not plugged.
