HALE HP 400 Скачать руководство пользователя

Страница: 36 / 72

HP SERIES
PORTABLE PUMPS

USER OPERATION AND MAINTENANCE

cartridge air dry thoroughly before

using.

CAUTION:

Petroleum solvents,

such as kerosene, are not to
be used to clean cartridge.
They may cause deterioration
of the cartridge. DO NOT OIL
CARTRIDGE. DO NOT USE
PRESSURIZED AIR TO CLEAN OR
DRY CARTRIDGE

3. Remove nut holding retainer
plate, cartridge and foam pre-
cleaner to top of engine.

4. Remove retainer plate and foam
pre-cleaner from cartridge.

5. Service foam pre-cleaner:

a. Wash in liquid detergent and

water.

b. Squeeze dry in a clean cloth.

c. Saturate in engine oil. Squeeze

in clean, absorbent cloth to remove

all excess oil.

6. Service cartridge:

a. Clean by tapping gently on flat

surface.

b. If very dirty, replace, or wash in

a low or non-sudsing detergent and

warm water solution. Rinse

thoroughly with flowing water from

mesh side until water runs clear. Let

AIR CLEANER

HOUSING

FOAM

PRE-CLEANER

AIR CLEANER

COVER

RETAINER PLATE

NUT

AIR FILTER COMPONENTS

CARTRIDGE

AIR CLEANER COVER

AIR CLEANER

COVER LATCH

AIR FILTER COVER REMOVAL

Содержание HP 400









































































Результаты поиска

Содержание HP 400

Отзывы:

Похожие инструкции для HP 400

Бренды по названию

Популярные бренды

HALE HP 400, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание HP 400

Отзывы:

Похожие инструкции для HP 400

Бренды по названию

Популярные бренды