background image

 Sec VI-14

Parts Lists

Booster

LIMITED WARRANTY

EXPRESS WARRANTY. Hale Products Inc. (“Hale”) hereby warrants to the original buyer that products
manufactured by Hale are free of defects in material and workmanship for two (2) years or 2000 hours usage,
whichever shall first occur. The “Warranty Period” commences on the date the Product is first placed in service.

LIMITATIONS. HALE’S obligation is expressly conditioned on the Product being:

Subjected to nominal use and service.

Properly maintained in accordance with HALE’S Instruction Manual as to recommended services
and procedures.

Not damaged due to abuse, misuse, negligence or accidental causes;

Not altered, modified, serviced (non-routine) or repaired other than by an Authorized Service
Facility.

Manufactured per design and specifications submitted by the original Buyer.

THE ABOVE EXPRESS LIMITED WARRANTY IS EXCLUSIVE. NO OTHER EXPRESS WARRANTIES ARE
MADE. SPECIFICALLY EXCLUDED ARE ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATIONS,
THE IMPLIED WARRANTIES OF MERCHANTABILITY; FITNESS FOR A PARTICULAR PURPOSE OR USE;
QUALITY; COURSE OF DEALING; USAGE OF TRADE; OR PATENT INFRINGEMENT FOR A PRODUCT
MANUFACTURED TO ORIGINAL BUYER’S DESIGN AND SPECIFICATIONS.

EXCLUSIVE REMEDIES. If Buyer promptly notifies HALE upon discovery of any such defect (within

the Warranty Period), the following terms shall apply:

Any notice to HALE must be in writing, identifying the Product (or component) claimed defective
and circumstances surrounding its failure.

HALE reserves the right to physically inspect the Product and require Buyer to return same to
HALE’S plant or other Authorized Service Facility.

In such event, HALE will provide a Returned Goods Authorization and Buyer must return the
Product F.O.B. within (30) days thereof;

If determined defective, HALE shall, at its option, repair or replace the Product, or refund the
purchase price (less allowance for depreciation),

Absent proper notice 

within 

the Warranty Period, HALE shall have no further liability or obligation

to Buyer therefore.

THE REMEDIES PROVIDED ARE THE SOLE AND EXCLUSIVE REMEDIES AVAILABLE. IN NO

EVENT SHALL HALE BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES

INCLUDING, WITHOUT LIMITATION, LOSS OF LIFE; PERSONAL INJURY; DAMAGE TO REAL

OR PERSONAL PROPERTY DUE TO WATER OR FIRE; TRADE OR OTHER COMMERCIAL

LOSSES ARISING, DIRECTLY OR INDIRECTLY, OUT OF THE PRODUCT FAILURE.

Содержание AP







































































Отзывы: