5
6
OPERATION
Use the pool’s current light switch to turn “ON” and “OFF” your new Halco ProLED White LED lamp.
TERMS AND CONDITIONS
This warranty is available to the original purchaser of the product(s) only. This warranty applies only
when products are properly installed in an in-ground pool; any other use voids the warranty. Products
must be used in lighting equipment designed and approved for the application and in environmental
conditions within the normal specified operating range. This warranty does not apply to any abnormal
use of product(s), use in violation of any applicable standard, code or instructions for use in installations
including those contained in the latest National Electrical Code (NEC), the Standards for Safety of
Underwriters Laboratory, Inc. (UL), Standards for the American National Standards Institute (ANSI).
This warranty will not apply in the event of conditions demonstrating abnormal use or stress, freezing,
operating when not fully submerged, under/over voltage/current condition, excessive switching cycles
or operating hours or outside the recommended operation conditions. This warranty does not apply to
color shifts or dimming caused by emissions and/or LED color shifts and dimming that naturally occurs
over time.
Warranty conditions: If the product operates for 15 or more hours per day or continuously
for 24 hours per day, the product warranty period stated shall be reduced to half the stated period.
This warranty does not cover damage occurring during shipment, damage or failure resulting from
alteration, accident, acts of God, theft, abuse, negligent installation, improper service, unauthorized
repairs, freezing or where adequate care has not been taken to prevent damage to the product(s).
Tampering with any internal component of this product(s) will void the warranty.
This warranty gives you specific rights. You may have other rights that vary according to the laws of your
state.
LIMITATION OF LIABILITY
THE FOREGOING SHALL CONSTITUTE THE EXCLUSIVE REMEDY OF THE PURCHASER AND IS IN LIEU
OF ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ALL WARRANTIES ARISING FROM
COURSE OF DEALING OR USAGE OR TRADE. THE LIABILITY OF HALCO UNDER THIS WARRANTY SHALL BE
LIMITED TO THE REPLACEMENT, REPAIR OR PRO-RATED CREDIT OF THE PRODUCT(S) AS STATED HEREIN.
HALCO IS NOT RESPONSIBLE FOR SHIPPING OR TRANSPORTATION COSTS RELATED TO OBTAINING
WARRANTY SERVICE. IN NO EVENT SHALL HALCO BE LIABLE FOR ANY OTHER COSTS OR DAMAGES,
INCLUDING LOST PROFITS OR REVENUES, LABOR CHARGES OR FOR ANY INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES.
Halco reserves the right to change the warranty and/or warranty period without prior notice and
without incurring obligation.
To obtain warranty service, retain the failed Product; retain the installation invoice showing product
purchase price and contact Halco ProLED Pool Customer Service at 800.374.1927
HALCO LIGHTING TECHNOLOGIES, 2-YEAR LIMITED WARRANTY
Halco Lighting Technologies (Halco) warrants the above-referenced model numbers of Halco ProLED
White LED Pool/Spa Lamp (the “Product”) to be free from defects in material and workmanship, under
normal use, conditions and service, for a period of two (2) year from the original date of purchase,
subject to the terms specified herein. If during the first (24) months of the warranty period, the Product
fails to operate due to a defect in material or workmanship, Halco will, at its option, repair or replace the
STEP 8
Check for air bubbles when light is turned ON.
Reconnect power to the pool light by resetting the circuit breaker to the “ON”
position. Go back to the light location and check for air bubbles rising to the surface
from the pool light housing for at least 10 minutes. It is important that the lamp
is turned on during this time. If you do not see air bubbles rising to the surface at
any time during the 10-minute inspection process, the housing is holding its water
tight seal and the installation is complete. You are ready to enjoy your new Halco
ProLED
®
White LED Pool lamp. If you do see air bubbles rising to the surface at any
time during the inspection process, immediately remove the Halco ProLED
®
White
LED lamp form the housing, dry it completely and reset the gasket and lens. Make
sure that the Halco ProLED
®
White LED lamp and light housing are completely dry
before reassembling. If the pool light housing continually leaks water after 2 or more
attempts at installation, replacement of the pool light housing may be necessary.
Please read the Halco ProLED
®
“White LED lamp Quick Start Guide” for further
installation device.
Note on Figures 1-3: All figures are provided for illustration purposes only. Refer to
