5. Operation
CAUTION
●
Since the end of the tip is thin, handle it carefully. If the tips and pipes
are bent, they may not be aligned properly even if they are adjusted.
●
When attaching/removing the tips, be sure to turn the power source OFF.
5-1 Handpiece
Adjust the positions of the tip ends with 4 wheels.
Afteradjustmentsaremade,closethetipsandconfirmthepositions
of the tip ends.
Angle adjustment wheel
Length adjustment wheel
Length adjustment wheel
Width adjustment wheel
Height adjustment wheel
Step 1 Length
Adjustment range: 0 to 1.5 mm
Length adjustment wheel
+
−
−
−
+
+
Step 2 Height and the tip end rotation angle
* J type in the illustration.
Adjust the height and tip end rotation angle alternately.
- Height
Adjustment range: The tip end moves up and down repeatedly within a
certain range when the wheel is turned.
Height adjustment wheel
- Rotation angle of the tip end
Adjustment range: approximately 200°
Angle adjustment wheel
Step 3 Width between the tips
Adjustment range: 0 to 10 mm
Width adjustment wheel
Open
Close
Open
Close
NOTE
5-2 Removing the tip
CAUTION
Perform procedures after the tip cools down.
Remove the tip using the iron cover on the iron holder after turning
the power source OFF.
(1) Slide the handpiece towards
the groove.
(2) Press the button with your
finger and fix the tip in place.
(3) If the handpiece is pulled
backwards, the tip will remain
in the groove.
(4) Place the tips in the tip storing
pocket.
There are grooves on both sides.
Button
Tip
Button
Tip storing
(1)
(2)
(3)
6. Maintenance
CAUTION
Do not file oxide attached on the tip.
This will shorten the tip lifespan.
The product can be used for a longer period of time in a higher quality by
periodically implementing maintenance. The rate of consumption varies
depending on the use temperature as well as the quality and quantity of
the solder and flux. Perform maintenance depending on your state of use.
(1) Turn the power source ON.
(2) Wipe the tip with a cleaning sponge after the temperature stabilizes.
(3) If there is black oxide on the solder plating, feed new solder containing
flux, and clean it off using a cleaning sponge. Repeat this until the
oxide is removed.
Then, cover it with new solder.
(4) Turn off the power source and remove the tip after it has cooled.
If there is oxide attached to parts other than the tip end, remove it
using alcohol, etc.
(5) Replace the tip if it is deformed or has worn.
Daily Maintenance
Before work
Wipe the oxide on the tip and old solder with a cleaning
sponge.
Foreign matter entering the P.W.B. will cause poor solder
application.
When work
is suspended
Enable Sleep [ON] and place the handpiece on the iron
holder. This will reduce oxidation of the tip. Turn off the
power switch when not using the product for a long peri-
od of time.
After work is
finished
Wipe the tip with a cleaning sponge and cover the tip end
with new solder.
This will prevent oxidation of the tip.
2021.3
MA03217Jb210301
© 2021 HAKKO Corporation. All Rights Reserved.
Please access the web address below for other distributors.
https://www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL: +81-6-6561-3225 FAX: +81-6-6561-8466
https://www.hakko.com E-mail: [email protected]
取説 FX-1003_EN_210301.indd 2
取説 FX-1003_EN_210301.indd 2
2021/03/01 13:19:53
2021/03/01 13:19:53
