中 文
English
日本文
29
Place the desoldered chip onto the tray
keeping the tips in parallel, and open
them to release.
NOTE:
Once the two tips are inserted into the
hand piece, heat control begins.
Both tips of the set must be inserted or
the handpiece will not heat.
CAUTION:
Very high tip temperatures may damage
the printed circuit board, possibly causing
the printed pattern to become detached.
HAKKO recommends setting the tip tem-
perature below 300°C for all normal work.
Using the lowest possible effective temper-
ature not only helps protect parts that are
sensitive to heat, it also helps protect the
tip from deterioration caused by heat.
A
B
6. When the set temperature is reached,
the buzzer sounds and the heater lamp
at the lower right of the temper ature
display starts blinking.
l
Operating instructions
1. Set the Temperature
CAUTION:
Never set the temperature to any value
over 400°C. Doing so may damage the
station. Set the temperature according
to the type of work to be done.
2. Switch lever on the handle
The MODEL FM-2023 is
double acting.
• When the tips are touching - i.e. the
handpiece is closed- an ‘R’ is visible on
the handle. Operate by squeezing the
movable part of the handle at the back.
• When the handpiece is open, an ‘N’
is visible on the handle. Operate by
squeezing the movable part of the
handle at the front.
3. Apply solder or flux
If there is insufficient solder on the
PWB, or the soldered area is too small,
apply solder or flux to the PWB. Solder
may also be applied to the tips.
4. Melt the solder
Place the tips on the soldered part and
melt the solder. Confirm that the solder
is fully melted. See sketch ‘A’.
5. Remove the component
After confirming that the solder is fully
melted, lightly squeeze the handpiece
to grasp the component and lift to re-
move the component. See sketch ‘B’.
Component
Solder
Содержание FM-2023
