background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning

・Unless 

otherwise 

directed, 

carry 

out 

these 

procedures 

with 

the 

power

 

 

switch 

OFF 

and 

power 

cord 

UNPLUGGED.

・Make 

sure 

the 

unit 

is 

sufficiently 

cool 

before 

proceeding.

 

 Remove the cover.

 Disconnect the sensor connector from the printed 

     wiring board and remove wire ties.

 Slightly widen the eyelet connector with  

     needle nose pliers and disconnect the sensor
     as shown in figure 2,3,4.

 Install the new sensor. Insert the sensor in 

     the correct position and squeeze the eyelet 
     connector with the needle nose pliers.
     (Refer to figure 5.)

 Reassemble in the reverse order of assembly.

 Turn ON the power switch. Check the temperature.

     Set the temperature control knob to 250

(482  ).

     Measure the temperature on the top of the outlet cover.
     The temperature should be approximately 250

(482  ). 

     If it is not, adjust by adjusting 
     potentiometer VR1 on the printed 
     wiring board as explained below.

  

Temperature adjustment

 Make sure the unit is completely cool, 

     then turn the power OFF and unplug the 
     power cord. 

 Remove the cover. Adjust VR1 with a 

     straight slot or small cross point
     screwdriver.  Turn clockwise to increase 
     temperature and turn counterclockwise to 
     decrease temperature.

 After the cover is attached, turn power ON, 

     and check the temperature.  

    

Caution :                                         

  If the adjustment level is set too high, the heater

    will operate continuously. If so, turn the VR1 
    counterclockwise till the lamp flashes.

11㎜

HAKKO 853 Replacing the sensor

Sensor

Sensor

connector

Figure 

1

Figure 

2

Figure 

5

(0.43in.)

F

°

F

°

Warning

Be sure to unplug the power cord when the 
cover is removed. Failure to do so may 
result in electric shock.

Sensor.

Sensor.

Eyelet

Eyelet

Figure 

3

Figure4

Squeeze 

gently 

until 

eyelet 

is 

round.

E

n

g

l

i

s

h


 

 



®

       HAKKO 853 

晩云易高兎 勧湖匂厚算圭隈

       

少御

・氏嗤乾窮議裡⑫。茅掲嗤蒙艶峺幣岻侃參翌,萩鳩範窮坿厮購渠,
  窮坿峨遊厮偉渠。
・字悶割蛍絶抜瘁壅序佩恬匍。

11㎜

勧湖匂

勧湖匂俊遊

(夕1)

①介和翌固。

②介和勧湖匂俊遊式鶴霜諏揮。

③參錫恁年嫖蝕署奉迅凛偉竃勧湖匂。(歌孚夕2、3)

④厚算仟勧湖匂。勧湖匂勣慧欺屎鳩岻了崔,
  參錫恁年容儿署奉迅凛遇耕協岻。(歌孚夕4)

⑤參㌢郡乏會廾指肇。

⑥嬉蝕窮坿,鳩範梁業。繍梁業距屁傴泥譜協壓250℃。
  勣壓患欠笥翌固岻嶄刹楚霞梁業。炎

寄埃頁250℃。

  梁餓湊寄扮,參窮揃医貧岻楚柴(VR1)距屁岻。

①字悶絶抜瘁,購渠窮坿蝕購,偉渠窮坿峨遊。

  ②介和翌固,參弌侏噴忖侘賜匯忖侘苔某答距屁
    窮揃医貧岻VR1。乏扮寞傴廬扮葎戻互梁業,
    郡岻夸週詰。

  ③廾貧翌固瘁,嬉蝕窮坿,旺鳩範梁業。

梁業距屁圭隈

 

   廣吭

距屁梁業扮,泌惚梁業湊互議三,辛嬬夛撹隔偬宥窮。

  隔偬宥窮扮,萩週詰梁業,
  岷欺窟犯圷周宥窮峺幣菊氏描妨葎峭。

勧湖匂

署奉迅凛

(夕2)

(夕3)

(夕4)

®




 

 

E

n

g

l

i

s

h

豫欺署奉迅凛撹垈侘葎峭.

Отзывы: