Haier WQP12-B9227E Скачать руководство пользователя | Manualshive

Страница: 9 / 38

background image

Inlet Valve

Theory of parts

-

>

3. Top panel

4. Left side panel

1. Baseboard

2. Left baseboard

5. Middle rear
crosspiece

Inlet valve

Access inlet valve

1. Disconnect power.
2. Remove the water inlet hose. (Note : Be careful of remain water drop.)
3. Remove the baseboard, left baseboard, top panel, left side panel and middle rear
crosspiece.

4. Disconnect the 2 terminal lugs
from the inlet valve.
5. Push the valve from the lower
rear crosspiece to take it off.
6. Remove the clamp and
disconnect the inlet hose (to air
breaker) from the water valve.
7. Reverse the above procedure
to install.

1.Open the control panel and take out the PCB;
2.Unplug the CON3 and P4 wires , then use the multi-
meter Ω shelf to measure resistance between the blue
wire (EV1) and white wire (IS), the normal resistance is
about 3.4KΩ to 4.3KΩ.
3. I f the measured resistance is not correct, it means the
valve coil is broken or the connector is loose. In this
case, we should check the connection first. If the
problem hasn’t been solved by re-connection, we should
replace the valve..
4.If the resistance is OK, we need to inspect the valve
body.

Inspect inlet valve

unplug

Check electric part

Attention:

Build in models have no Baseboard and

left and right baseboard, but adjustable baseboard.

-

9 -

IS

EV1

«
...
7
8
9
10
11
...
»

Содержание WQP12-B9227E







































Отзывы:

Нет отзывов

Похожие инструкции для WQP12-B9227E

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 12

Бренд: Kleenmaid Страницы: 30

Бренд: Bush Страницы: 44

Бренд: NewAir Страницы: 24

SmartWasher BenchtopPRO

Бренд: CRC Страницы: 4

LVSLS11C45GZ17S

Бренд: Saba Страницы: 35

Бренд: Daewoo Страницы: 57

Бренд: Smeg Страницы: 29

Бренд: Newworld Страницы: 41

Бренд: Smeg Страницы: 14

WF8694AH(A/C/D/F/G/H/R/S/T/V/W/Z)(U)

Бренд: Samsung Страницы: 72

Бренд: Samsung Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды