background image

3.SPECIFICATION

The dimensions for the condensing unit are illustrated in 

Figure 1

. Physical and electrical

specifications are provided in 

Table 1

.

Figure 1

H

W

1.INTRODUCTION

This manual contains the installation and operating instructions for your new air conditioner.
Improper installation can result in unsatisfactory operation or dangerous conditions.  Carefully
read this manual and any instructions packaged with separate equipment required to make up
the system prior to installation. Give this manual to the owner and explain its provisions. The
owner should retain this manual for future reference.

2.NOMENCLATURE FOR MODEL NUMBER

1

D

X

X

X

XX

X

X

X

G=  9 SEER

H=Horizontal Flow

                                                                                                                   

Efficiency

   

H= 10 SEER

V=Vertical Air Flow

                                                                                                                                       

J= 13 SEER

1= R22

                                                                                                                                                          

2= 208/230V-1Ph-60Hz

3= 208/230V-3Ph-60Hz

First Generation

                                                                                                                       

Voltage

  

    

4= 220/240V-1Ph-50Hz

5= 380V-3Ph-50Hz

6= 380V-3Ph-60Hz

18= Capacity Btuh

Application

   

C

 

= Cooling

    

H= Heat Pump

Содержание V1124C2H


















Отзывы: