To connect the drain pipe
Ring the drain pipe on the joint;
F
i
x
the pipe clamp to the groove of drain pipe;
Insert the drain pipe into a floor drainer;
Ex
tend the drain pipe.
State of
e
x
tension hose
Height Length
Rise midway
Within 10cm
N
ot rise
midway
-
If the drain pipe is too long, remove the pipe sleeve, cut
off the groove part of drain pipe, and then insert the pipe
sleeve into the front end of drain pipe.
If there is a need to e
x
tend the drain pipe or change the direction of drain pipe, please contact our
A
fter-sales Service Department.
To remove the packaging
bolts
Packaging bolts are used to fi
x
internal components of the
washer-dryer during transport and should be removed before
using the washer-dryer.
Screw off all the packaging bolts with a wrench and pull
them out in the direction as shown in the right figure;
Insert the heave of packaging bolt cover into the
packaging bolt cover hole, and then buckle the packaging
bolt cover into the packaging bolt hole in the direction of
arrow as shown in the right figure.
Please keep the dismantled packaging bolts in a safe place
for future handling of
the washer-dryer.
To adjust the front
adjustable foot (2)
Loosen the adjusting nut, and then
adjust the adjustable foot (as shown in
F
ig.1) until the air bubble of level gauge
is in the red circle (as shown in
F
ig. 2).
Tighten the adjusting nut (as shown
in
F
ig.
3
).
Within
3
m
Within 1m
Within 10cm
F
loor
drainer
F
loor
Within 1m
Pipe sleeve
Drain outlet
Stay a space
G
roove
Pipe sleeve
Before removing the
packaging
bolts, please fi
x
the
A
nti Rat
C
over to the bottom of the washer dryer.
Lay down the machine, adjust the
A
nti Rat
C
over with the seven holes corresponding the screw holes.Then
tighten the screws and fi
x
it thus securely to the bottom of the machine.
To install the Anti Rat Cover
F
ig. 1
F
ig.
2
F
ig.
3
Loosen
High
Low
Tighten
A
djusting
nut
A
djustable foot
Packaging
bolt hole
Packaging bolt
cover hole
Heave
Pipe clamp
Joint
G
roove Drain pipe
11 Preparations before Washing
C
heck the articles to be washed for special washing requirements and make sure that they are
machine washable and dryable to avoid deformation and damage.
F
or those articles tainted with much mud and dust, please remove them before washing.
Wash those articles liable to color fading separately from others.
C
heck pockets and remove coins, sand, hairpin and other things from them.
Tie the ties, buckle the buttons, zip the zippers and sew the openings.
To avoid the sound from buttons, please turn those articles with buttons inside out before putting
them in the washer-dryer.
Do not overload the washer-dryer.
F
urthermore, please unfold and fluff out the articles before
putting them in the washer-dryer.
When washing small articles and those articles liable to inter-twist and wear, please put
them in net bags for washing, rinsing and spinning to avoid damage.
12 Reference Weight for Different
Types of Clothing
A
suit of work clothes
Blended fabric,
about
8
00g
A
suit of pajamas
C
otton, about
3
00g
Shirt
Blended fabric,
about 200g
Undershirt
C
otton, about 1
3
0g
Bath towel
C
otton, about
3
00g
Briefs
C
otton, about
7
0g
Socks
C
otton, about
3
0g
Jeans
C
otton, about
6
00g
7
1
6
