Haier LMD1841B0 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 19

Haier LMD1841B0 Скачать руководство пользователя страница 7

Chapter 6: INSTALLA TION AND ACCESSORY PARTS

6

5. If the extra hose is too long, cut it either

at point A or B.

B

A

> 30mm

<1.5m

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be

less than 10cm , or the drainage will

not be smooth enough and cause

incomplete drainage.

2.Do not tramp or press the drain hose.

3.If the drain hose is too long, cut it at mid point.

To make smooth drainage, cut the front end of

the hose slantingly.

4.If extra drain hose is needed , please make

separate purchase. The inner diameter of the

extra hose shall not less than 30mm, and the

length shall not exceed 1.5m.

<10cm

Overflow filter

Lint filter

Please install and adjust the machine according to the requirement of

the manual. It is very important to your security and correct operating

the machine.

Install the lint filter

After opening the package,please take out the lint

filter from the document bag,install it to the overflow

filter of the wash tub.See to the figure.

Usage of the drain hose

6.1 Dismantle and installation

Figure 1

Service Manual

Issue

Rev.

LMD1841B0

、

LMD1842B0

«
...
5
6
7
8
9
...
»

Содержание LMD1841B0




















Отзывы:

Нет отзывов