1
6
5
2
1
4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
Display board
Outdoor Unit
Signal receiver hole
COOL
display
HEAT
display
HEALTH display
Dry
display
4
2
3
1
6
6
7
5
4
2
1
5
3
5
2
1
5
3
6
8
8
1
4
Parts and Functions
Indoor Unit
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust up and down air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
4
2
3
1
6
5
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
(
If the unit which you purchased
has healthy function,follow it.
TIMER OFF display
TIMER ON display
SLEEP display
Remote controller
1
2
3
5
6
7
8
9
10
4
ON/OFF
HEALTH
FAN
MODE
SWING
TIMER
CLOCK
SET
SLEEP
LOCK
RESET
11
12
14
15
16
17
13
18
19
20
21
22
23
23
1. Operation mode display
23. HEALTH
.
n
o
it
c
n
u
f
Ope
r
ation mode AUTO
FAN
COOLDRY
Remote controller
Display board
HEAT
2. SWING display
3.FAN SPEED display
4. SLEEP display
5. LOCK display
6. SIGNAL SENDING
7.TIMER OFF display
8. TIMER ON display
9. CLOCK display
10. TEMP display
11. POWER ON/OFF
Used for unit start and stop.
12. MODE
Used to select AUTO run,
COOL,DRY,HEAT and
13. FAN
Used to select fan speed
14. HOUR
Used to set clock and timer
15. SWING
Used to set auto fan direction.
16. SLEEP
Used to select sleep mode.
17. LOCK
Used to lock buttons and
18. TEMP.SETTING
Used to select your desired
19. SET
Used to confirm timer and
20. TIMER
Used to select TIMER ON,
TIMER OFF,TIMER ON-OFF
21. CLOCK
Used to set correct time
22. RESET
back to normal condition.
Used to reset the controller
LO
MED
HI
AUTO
FAN operation
LO, MED, HI, AUTO
setting.
LCD display.
temp.
clock settings.
If not,please ignore.
)
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have displays and functions related with heating
4
7
Ambient temp.display
When receiving the remote control signal,
display the set temperature and in the rest
this room temperature is only for reference.
time the room temperature is displayed and
1
2
3
4
1
2
3
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the button is kept pressed,time will
TIMER
CLOCK
SET
SLEEP
LOCK
RESET
will increase
(inside)
Anion generator
7
7
Used to operate the healthy
