«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
«Î—°”√Õ¨“ª∆∑≈∆¡ΩΩ⁄
7#
µÁ≥ÿ,≥§ ±º‰≤ª”√ ±,Œ™
∑¿÷𬩓π«ÎΩ´µÁ≥ÿ»°
≥ˆ°£
‘⁄ π”√÷–»Á”ˆ“Ï≥£,«Î
Ω´µÁ≥ÿ»°≥ˆ,6∑÷÷”∫Û‘Ÿ
◊∞»Î–¬µÁ≥ÿ°£
∫£∂˚ºØÕ≈«‡µ∫∫£∂˚
ø’µ˜∆˜”–œfi◊‹π´Àæ
4
Operation
Remote controller's operation
When in use, put the signal transmission head directly to the
receiver hole on the indoor unit.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
Don't throw the controller, prevent it from being damaged.
When electronic-started type fluorescent lamp or change-over
type fluorescent lamp or wireless telephone is installed in the
room, the receiver is apt to be disturbed in receivering the signals
so the distance to the indoor unit should be shorter.
Loading of the battery
Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder)
Remove the battery cover:
Slightly press " " and push down the cover.
Load the battery:
Be sure that the loading is in line with the" + "/"-"
pole request as illustrated.
Put on the cover again
Confirmation indicator:
In disorderation, reload the batteries or load the new batteries after 6mins.
Note:
Use two new same-typed batteries when loading.
If the remote controller can't run normally or doesn't work at all,
use a sharp pointed item to press the reset key.
Hint:
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out just need to press reset key.
