Haier GE NS22HM, Руководство по обслуживанию

Страница: 102 / 106

3DJH
31-5000750 Rev. 1
°F Psig °F Psig °F Psig °F Psig °F Psig °F Psig °F Psig °F Psig
32 100.8 48 137.1 63 178.5 231.6 110 365.0 125 141 545.6
33 64 181.6 80 235.3 111 370.0 126 451.8 142 552.3
34 105.0 50 142.2 65 184.3 81 112 375.1 127 457.6 143
35 107.1 51 144.8 66 187.7 82 242.7 303.8 113 380.2 128 463.5 144
36 52 147.4 67 83 246.5 308.2 114 385.4 145 572.8
37 111.4 53 150.1 68 84 250.3 312.7 115 130 475.6 146
38 113.6 54 152.8 85 254.1 100 317.2 116 131 481.6 147 586.8
115.8 55 155.5 70 200.6 86 258.0 101 321.8 117 401.3 132 487.8 148
40 118.0 56 158.2 71 87 262.0 102 326.4 118 406.7 133 601.0
41 120.3 57 161.0 72 207.2 88 266.0 103 331.0 412.2 134 500.2 150 608.1
42 122.6 58 73 210.6 270.0 104 335.7 120 417.7 135 506.5 151 615.4
43 125.0 166.7 74 214.0 274.1 105 340.5 121 423.2 136 152 622.7
44 127.3 60 75 217.4 278.2 106 345.3 122 428.8 137 153 630.1
45 61 172.6 76 282.3 107 350.1 123 434.5 138 525.8 154 637.5
46 132.2 62 175.4 77 224.4 286.5 108 355.0 124 440.2 532.4 155 645.0
47 134.6 78 228.0 360.0 140
Table 32. HFC-410A Temperature (°F) - Pressure (Psig)
Figure 53. Using HFC-410A Subcooling Method - High Speed (High Capacity)
1. THE DIAGNOSTIC SCREEN ON THE THERMOSTAT OR OUTDOOR CONTROL 7-SEGMENT DISPLAY WILL SHOW INDOOR AND
OUTDOOR MOTOR CFMS OR RPMS.
2. MEASURE OUTDOOR AMBIENT TEMPERATURE.
3. CONNECT GAUGE SET.
4. CHECK LIQUID AND VAPOR LINE PRESSURES. COMPARE PRESSURES WITH COOLING MODE NORMAL OPERATING
PRESSURES IN THE APPLICABLE CHARGING STICKER, NORMAL OPERATING PRESSURES AT MAXIMUM CAPACITY.
NOTE
-
THE REFERENCE TABLE IS A GENERAL GUIDE. EXPECT MINOR PRESSURE VARIATIONS. SIGNIFICANT
DIFFERENCES MAY MEAN IMPROPER CHARGE OR OTHER SYSTEM PROBLEM.
5. SET THERMOSTAT FOR HEAT/COOL DEMAND, DEPENDING ON MODE BEING USED:
USING COOLING MODE
— WHEN THE OUTDOOR AMBIENT TEMPERATURE IS 60°F (15°C) AND ABOVE. TARGET
SUBCOOLING VALUES (MAXIMUM / 100% CAPACITY) IN APPLICABLE CHARGING STICKER ARE BASED ON 70 TO
80°F (21-27°C) INDOOR RETURN AIR TEMPERATURE; IF NECESSARY, OPERATE HEATING TO REACH THAT
TEMPERATURE RANGE; THEN SET THE INITIAL COOLING DEMAND AT MAXIMUM CAPACITY. THE PREFERRED METHOD IS
TO USE THE “CHARGE MODE” JUMPER ON THE OUTDOOR CONTROL. SEE CHARGE MODE JUMPER SECTION ON PAGE 80.
WHEN PRESSURES HAVE STABILIZED, CONTINUE WITH STEP 6.
6. READ THE LIQUID LINE TEMPERATURE; RECORD IN THE LIQº SPACE.
7. READ THE LIQUID LINE PRESSURE; THEN FIND ITS CORRESPONDING TEMPERATURE IN THE TEMPERATURE/ PRESSURE
CHART LISTED IN THE APPLICABLE CHARGING STICKER AND RECORD IT IN THE SATº SPACE.
8. SUBTRACT LIQº TEMPERATURE FROM SATº TEMPERATURE TO DETERMINE SUBCOOLING; RECORD IT IN SCº SPACE.
9. COMPARE SCº RESULTS WITH APPLICABLE CHARGING STICKER, BEING SURE TO NOTE ANY ADDITIONAL CHARGE FOR
LINE SET AND/OR MATCH-UP.
10. IF SUBCOOLING VALUE IS GREATER THAN SHOWN IN APPLICABLE CHARGING STICKER FOR THE APPLICABLE UNIT,
REMOVE REFRIGERANT; IF LESS THAN SHOWN, ADD REFRIGERANT.
11. IF REFRIGERANT IS ADDED OR REMOVED, REPEAT STEPS 6 THROUGH 10 TO VERIFY CHARGE.
12. DISCONNECT GAUGE SET AND RE-INSTALL BOTH THE LIQUID AND SUCTION SERVICE VALVE CAPS.
USE
COOLING
MODE
USE
HEATING
MODE
60ºF
(15ºC)
SATº
LIQº –
SCº =
SUBCOOLING
CHARGING METHOD
(All charging MUST be performed while system is operating
either at maximum speed or 100% demand.)