Haier GE GDF510P M4 Series Скачать руководство пользователя страница 12

Страница: 12 / 79

– 12 –

Troubleshooting

• Check voltage input to the dishwasher.

• Verify door switch operation, consult

Consumer Error Mode

, in the

Electronic Controls

section of

this service guide.

• Door must be closed within 5 seconds of pressing Start Pad (Safety Feature).

• Check the main board Service LED (see

Main Control Diagnostics

Electronic Controls

• Verify that the dishwasher is not in

Demo Mode

• CSM (Current Sense Module) tripped. Please refer to

On the Main Control Board CSM

in the

Electronic Controls

section of this guide.

This troubleshooting section is an overview of diagnostic capabilities of the electronic control. The

control also features retrieval of fault codes when Consumer Error Mode is initiated; operation of loads

is achieved in Service Mode.

Details on Consumer Error Mode and Service

Mode, as well as Service LED are located in the

Electronic Controls

section of this service guide.

Single mounting screw

If the control beeps and some LED's flash, this indicates the dishwasher door may be in the open

position. If the User Interface (UI) is flashing all the LED's or the Display (some models) is flashing, this

is an indication of a tripped CSM and the dishwasher is non-responsive, all the LED's will flash until the

CSM is reset. CSM diagnostics are covered in this service guide.

Flashing Lights

Will Not Start

Symptom

: If the dishwasher is “dead”, no LED operation, no button operation or beeping occurs.

Diagnosis

: Attempt placing the dishwasher in Consumer Error Mode.

Solution

: The CSM (Current Sense Module) is tripped and must be fully diagnosed. Refer to

the Main Control Board CSM

section of this guide.

Symptom

: If the start button

either

does not respond or it makes a triple beep sound

every time it’s

pressed

AND

all other buttons respond as normal.

Diagnosis

: The dishwasher may be in Demo Mode.

Solution

: To exit Demo Mode, hold “SELECT CYCLE” and “HEATED DRY” at the same time for 5

seconds.

Содержание GE GDF510P M4 Series
















































































Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды

Haier GE GDF510P M4 Series, Руководство по обслуживанию

Результаты поиска

Содержание GE GDF510P M4 Series

Отзывы:

Похожие инструкции для GE GDF510P M4 Series

Бренды по названию

Популярные бренды