Haier GE DDT700S N0 Series Скачать руководство пользователя

Страница: 29 / 78

– 29 –

The door has DC voltage only and has a

screwless appearance. The door contains a User

Interface (UI) Board with all tactile switches on

the board. Some models have a seven-segment

display; others have LED indicator lights. The

door also houses the detergent module, bottom

door seal and a venting system (see the

Dry

System

section in this service guide).

Door Removal

1. Remove power to the dishwasher, close and

latch the door.

2. Remove the toe kick and insulation, if

applicable.

3. Disconnect the door wire harness at the

bottom of the main control cover.

4. Release the wire clip holding the harness

to the tub. Push up on the wire harness to

release the harness.

WARNING: GE Factory Service Technicians

are REQUIRED to follow Lockout / Tagout

(LOTO) 6 Step Process prior to beginning

repair.

5. Locate the door balance cable and insert an

Allen wrench or tool formed into a hook (as

shown below).

6. Lift the cable up and slide forward.

7. Slide the cable down and away from the

dishwasher. Do not release tension from the

cable.

(

Continued next page

)

Door

Содержание GE DDT700S N0 Series















































































Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды

Haier GE DDT700S N0 Series, Техническое обслуживание руководство

Результаты поиска

Содержание GE DDT700S N0 Series

Отзывы:

Похожие инструкции для GE DDT700S N0 Series

Бренды по названию

Популярные бренды