Haier ESD 300 Series Скачать руководство пользователя страница 70

Страница: 70 / 93

DIAGNOSTICS

Indicator Lamps

Water Heated (ESD310-311-312) Indicator glows only when the cycle pauses to heat water to a set temperature.
Washing or rinsing continues as the water is heated. Once water reaches the set temperature, the light goes off and
the cycle resumes.

Washing (ESD310-311-312) Indicator glows during the pre-wash and main wash periods.

Turbidity Sensor (ESD310-311-312) Indicator glows during the sensing part of the cycle. Washing continues during
the sensing.

Rinsing (ESD310-311-312) Indicator glows during the rise periods.

Drying (ESD310-311-312) Indictor glows during the drying cycle after the final rinse.

Clean Indicator glows when a wash cycle is complete and will remain ON until the door is opened.

Sanitized Indicator glows when the cycle has met sanitization conditions. The light will remain ON until the door is
opened.

Add Rinse Aid (ESD310-311-312) Indicates the Rinse Aid Dispenser is empty. The indicator glows while a cycle is running.

Содержание ESD 300 Series






























































































Результаты поиска

Содержание ESD 300 Series

Отзывы:

Похожие инструкции для ESD 300 Series

Бренды по названию

Популярные бренды

Haier ESD 300 Series, Руководство по обслуживанию

Результаты поиска

Содержание ESD 300 Series

Отзывы:

Похожие инструкции для ESD 300 Series

Бренды по названию

Популярные бренды