1
2
Make 2 holes Φ 12mm, 65mm deep in wall with an
impact drill according to the drawing of the external
dimensions (See Figure 4).
Take out all accessories in packaging liner, unpack
one hook, sleeve the ring end of the connection lines
among the accessories into the hook tightening end
and assemble the hook well.
right hole).
Lift the water heater and hang it with wall rack corresponding to the two hooks. Insert the
connection spacer led from the rear shell wall rack of the heater into the connection terminal
of the line on the hook (See Figure 2).
appropriate locations on inlet and outlet pipes respectively. Find the location requiring hot
water supply. Connect inlet pipe, outlet pipe and city water pipe respectively to the use point
for hot water. Fill the tank with water to check whether there is any leakage. It must be re-
connected if there are signs of water leakage.
Warning:
Do not release your grip unless the wall rack is securely hung on the hook.
Otherwise the heater may fall and cause personal injury or property damage.
Connect the safety valve to the water inlet by following the direction of its arrow (the arrow
should point towards the heater). The safety valve’s rated pressure is 0.80MPa and its connection
is G1/2. Once power is connected and the water is being heated, the water inside the water
tank will expand. In order to relieve the water pressure inside, a very
safety valve. The pressure-relief vent must be free of any blockages.
Please connect the drain hose to the safety valve. Connect one end
of the hose to the safety valve vent and the other end to the sewage
drain. The hose can be cut short or extended as necessary. The hose
shall be installed as inclined downward.
ES15V-P2
ES25V-P2
ES35V-P2
Spa Water Heater
User's Manual
SPEED
SET
TIMER
0040502425
V
SPEED
SET
TIMER
Please read this manual before usage.
Retain it for future reference.
Safety warning (Read carefully before use)
Installa
tion •
Use
Installation must be made by installers of or designated by our company after-service department.
The water heater shall be wall-mounted.
Installation
Installing safety valve
FAQ
Phenomenon
Remedy
No water
No water supply or water pressure
is too low
Check
Water use point is blocked or hot
water valve is closed
Check and clear
Cold outlet water
1
Hot water access close
Check and open
2
Temperature not set to desired
setting
Calibrate the heater according to the
operation instructions in the manual
3
Heating time limit and setting
temperature not obtain
Calibrate the heater by referring to
the operation instructions in the
manual
4
Defective elements
Contact with service department
when
1
,
2
and
3
are excluded.
Not heated to
desired temperature
water
1
Whether the current function
is set to the proper mode and
temperature is set too low.
Calibrate the heater according to the
operation instructions in the manual
2
Excessive water pressure
turned down
temperature of water Inconstant water pressure
turned down or use with constant
water pressure
Incapable of startup
or display not lit
1
No power to heater
Check power socket
2
Defective elements
Contact with service department
when
1
is excluded.
Display E1
Faulty line
Contact with service department
Display E2
1
Power on after disconnection when
2
Defective elements
Contact with service department
when
1
is excluded.
Display E3
1
Room temperature lower than
-20°C
when ambient temperature more
than -19°C
2
Defective sensor
Contact with service department
when
1
is excluded.
Meanings of icons
These are
actions which
are forbidden
These are actions
which must be
carried out
These are matters
for which attention
is required
Forbidden
Warning
CAUTION
If the water heater emits an unusual
smell or a burning smell, please
disconnect the power supply
immediately and call the service center.
This mark is the designation
for Pre-safe Expert of Haier
Water Heater Company,
which indicates the use of
the company's patented
technology inside the product. It ensures
you a safe bath while monitoring whether
your house ground wire is live or not all
the time. If this mark is lit, it indicates your
house ground wire was come live (poor
grounding and live). In this case, please
immediately stop use and disconnect
the power, and remember not to touch
any electric applicance in your house.
At the same time, immediately contact
after-sales service and your property
management company for professional
Non-professional maintenance
personnel shall not carry out
unauthorized repair, maintenance,
dismantling or re-construction of
the heater.
Be sure to use independent socket
and earth it reliably.
In case the power cord of the
water heater is damaged, be sure
to have it replaced by after service
technicians with special cord
If you do not need to use the heater
for a prolonged period, please cut
in the heater in accordance with
the instructions in the chapter on
cleaning and maintenance.
Earthing
Take care not to be scalded by hot water.
•
Do not touch the valve and pipe for hot
water supply.
•
Please feel the water temperature before
use. Use only when the temperature is
ideal for you.
Do not set at outdoor places.
Do not install the water heater in the
conditions in which ice could form.
Ice formation will cause the water
container and piping to crack, leading
to scalds and water leakage.
Do not connect or disconnect the power
supply while your hands are wet.
Check if the ammeter and the
diameter of the wires are in
accordance with the rated current
of the water heater. If necessary,
please have it checked by an
experienced electrician.
Do not drink hot water from the
heater or use it for similar purposes.
Do not spray water or steam onto
the heater.
Please take precautionary measures
during cold weather so as to prevent
the heater from being frozen.
reliable wall.
Do not install at places without sewage.
Warning
Warning
Warning
Warning
(Figure 1) for installation
reference only.
Hot water
outlet
Safety valve
Cold water
inlet
Shower
head
Cold
water
outlet
valve
Mixing
Valve
Hot
water
outlet
valve
(Figure 2)
Extended connection line
Wall rack
Expansion
hook
SPEED
SET
TIMER
1
2
3
4
(Figure 1) for installation
reference only.
Cold
water
outlet
valve
Mixing
Valve
Hot
water
outlet
valve
(Figure 2)
Extended connection line
Wall rack
Expansion
hook
Connect to drain hose
(Figure 3)
CAUTION
CAUTION
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
