Starting the Appliance
Starting a wash cycle
After having completed all of the installation steps in the preced-
ing paragraphs, turn on the water all the way and press the ON-
OFF button (A) located on the control pannel. The appliance is
on (see fig.1).
Cancelling or modifying a cycle
A cycle that is underway can only be modified if it has only been
running for a short time. Otherwise, the detergent may have al-
ready been used, and the appliance may have already drained
the wash water. If this is the case, the detergent dispenser must
be refilled (see the paragraph entitled, "Loading the Detergent").
To modify a cycle that is already underway, press the start- pause
button (E) for 5 second, all of the settings will be cancelled. To
set a new cycle, follow the instructions contained in the para-
graph entitled "Setting and starting a wash cycle".
Setting the Wash Cycle with a Delayed Start Time
Button for "extre drying" or "half load" or "delay"
By pressing the "D" button in sequence ,the selection cursor (Q)
will come on in turn :
Extre drying -- Half load --Delay -- Extre Half load --Extre
Delay --Half load +Delay -- Extre Half load + Delay
Extre drying
By pressing the "D" button,the drying time of extre drying will be
longer ,and the drying relating is better.
Half load
By pressing the "D" button,this button (see "close-up View - Con-
trol Panel", letter "D") makes it possible to wash dishes using
only the upper rack if there are not enough dishes for a full load.
This will allow you to save on water and power. It can be used
before setting any of the wash cycle, except for the intensive
cycle ( if included in the wash cycle table). Please keep in mind
that the amount of detergent should also be cut in half.
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íçå
`óÅäÉ=éÜ~ëÉ=ìåÇÉêï~ó=áåÇáÅ~íçå
The dishwasher is equipped an indecation "P" comprissing 4
symbels which represerd the diferent phases of a wash cycle.
When the wash cycle has started,the displace will indicate ,the
phase under way in sequence.There place are pre-wash,wash,
rinse,drying.
During the delay period, it is preferable not to change any of the
settings, If this is necessary, all of the settings must be cancelled
by pressing the ON/OFF button (A).
At this point, all of the steps for "setting the wash cycle with a
Delayed Start Time" and "Setting and Starting a wash cycle" must
be repeated, following the instructions contained in the corre-
sponding sections.
If the door is opened to the unit during the delay period, the count-
down will stop. It wil begin again when the door is closed.
All of the wash cycle set to reverse time function, we may
in focus start circulate time.
At the end of the wash cycle
Six beeps will indicate that the wash cycle has finished and the
LCD display (B) will come on (see fig.1). Turn off the appliance
using the ON-OFF button. Turn off the water supply to the appli-
ance and open the door. Wait a few minutes before unloading
the dishwasher to avoid handling the dishes and utensils while
they are still hot and more susceptible to breakage. They will
also dry better.
Setting and Starting a wash Cycle
Select the desired cycle by pressing programme selection but-
ton (F). Each time the button is pressed, the seletion cursor"Q"will
come on in succession. Choose the wash cycle you feel is most
appropriate for the type of dishes that need washing (consult the
wash cycle table contained in this manual. After press the start-
pause button(E), the wash cycle has begun and can no longer
be changed. If necessary, read the paragraph entitled "Cancel-
ling or modifying a cycle"
Wash Cycle Program Light
The dishwasher is equipped with a LCD indicator light (G) that
turns on when the appliance is running the wash cycle.
By pressing the "D" button (see close-up view-'Control panel"),
select ,and the selection cursor turns on,then pressing the
"C" button ,the start of wash can be delayed for between 1 to 12
hours.
Each time the "L" button is pressed, the display (M) will show the
number of hours for the delay period. Choose the amount of time
desired. After selecting the wash cycle, pressing the start-pause
button(E), the delay time on the display will blink.This indicates
that the countdown has begun.
After the time has alapsed, the cycle will start.
NOTE:
Wash Cycle adjustment Buttons
.6.
GB
pre-wash wash rinse drying
