background image

SAFETY  PRECAUTIONS

5

1. Applicable ambient temperature range:

The machine is adaptive in following situation

Cooling

Heating

Indoor

Indoor

Outdoor

Outdoor

Maximum:
Minimum:

Maximum:
Minimum:

Maximum:
Minimum:

Maximum:
Minimum:

D.B / W.B
D.B / W.B

D.B / W.B
D.B / W.B

D.B / W.B

D.B / W.B

D.B

D.B
D.B

32     / 23
18     / 14

-7     / -8

24     / 18

43

15

15

27

/ 26

2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent

    or a similar qualified person.

3. If the fuse on PC board is broken please change it with the type of  T. 3.15A /2500.

4. The wiring method should be in line with the local wiring standard.

5. The power cable and connecting cable are self-provided. The power cable should be

   5x5.0mm

2

 .The connecting cable should be 4x2.0mm

2

.

    All the cables shall have got the European authentication certificate. During installa-

    tion, when the connecting cables break off, it must be assured that the grouding wire is

    the last one to be broken off.

6. The breaker of the air conditioner should be all-pole switch; and the distance between its

    two contacts should be no less 3mm.

7. The indoor unit installation height is at least 2.5m.

Installation and maintenance must be meet the local installation and miantenance instructions and
should operate by the experienced special installation and maintenance technicians .itherwise  we
donít take any duty of  the units damage or injure to the person caused by improper operation.

NOTE!

1.The sharp edges and corners and coil surface have the danger to  injury ,should avoid of them;
2.Itís very danger to remove the units and power supply wire.because it can cause injury and death .
Cut off all the power supply before mintenance.

WARNING!

Содержание AD88NAHAAA









































Отзывы: