background image

1

1

3

3

 

The thermostat supports the following command classes: 
 

COMMAND_CLASS_THERMOSTAT_MODE 
COMMAND_CLASS_THERMOSTAT_SETPOINT 
COMMAND_CLASS_THERMOSTAT_FAN_MODE 
COMMAND_CLASS_THERMOSTAT_FAN_STATE 
COMMAND_CLASS_THERMOSTAT_OPERATING_STATE 
COMMAND_CLASS_SENSOR_MULTILEVEL 
COMMAND_CLASS_ASSOCIATION 
COMMAND_CLASS_CONFIGURATION 
COMMAND_CLASS_VERSION 
COMMAND_CLASS_MANUFACTURER_SPECIFIC 
COMMAND_CLASS_SWITCH_BINARY 
COMMAND_CLASS_CLOCK 

 
COMMAND_CLASS_THERMOSTAT_MODE 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
set the mode, get the current mode, and get the modes supported by the thermostat. 

 
COMMAND_CLASS_THERMOSTAT_SETPOINT 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
change setpoints, get current setpoints, and request the setpoints that are supported by thermostat. 

 
COMMAND_CLASS_SENSOR_MULTILEVEL 

 
The RC-100BZ thermostat uses this command class to report the actual temperature. 

 
COMMAND_CLASS_ASSOCIATION 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
issue an Association Set, Remove, or Get command.  The thermostat must be associated with a controller to 
provide feedback. 

 
COMMAND_CLASS_CONFIGURATION 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
change individual register settings for the outdoor temperature.  The Parameter Number is 67.  The size of the 
data is a 1 byte value.  The Value is the temperature to which the register is set. 

 
COMMAND_CLASS_THERMOSTAT_FAN_MODE 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
set the fan mode, get the current fan mode, and get the fan modes supported by the thermostat. 

 
COMMAND_CLASS_THERMOSTAT_FAN_STATE 

 
Upon power up, allow 10 seconds for the RC-100BZ thermostat to initialize.  After 10 seconds, a controller can 
request the state of the fan.

 

Содержание RC-100BZ

















Отзывы: