HAI UPB™ 8-BUTTON HOUSE CONTROLLER OPERATION
The HAI UPB™ 8-Button House Controller has many configurable items that can be set using the UPB™ UPStart configuration
software. The following describes the operation of the HAI UPB™ 8-Button House Controller in its factory default configuration.
Using Pushbuttons to Control Individual Lighting Loads
In its factory default configuration, all 8 pushbuttons are configured to toggle between two different actions each time a pushbutton is
pressed. Likewise the LED indicator behind the pushbutton will toggle when the pushbutton is pressed.
Linking Pushbuttons to HAI UPB™ Wall Switch Dimmer(s)
To configure these actions, the pushbuttons on the HAI UPB™ 8-Button House Controller must be linked to HAI UPB™ Wall Switch
Dimmer(s) as follows:
Step Operation
1
Use the local Decora-style rocker switch on the HAI UPB™ Wall Switch Dimmer(s) to set the desired level(s).
2
Tap the Decora-style rocker switch on the HAI UPB™ Wall Switch Dimmer(s) five (5) times quickly.
3
The HAI UPB™ Wall Switch Dimmer will flash its lighting load one time and blink its LED blue, to indicate that it is
ready to be linked.
4
Press the pushbutton on the HAI UPB™ 8-Button House Controller five (5) times quickly.
5
Each HAI UPB™ Wall Switch will flash its lighting load one time to indicate that it is successfully linked to the
pushbutton and that the new light level has been set.
Unlinking Pushbuttons from HAI UPB™ Wall Switch Dimmer(s)
If you accidentally link the wrong pushbutton to the wrong HAI UPB™ Wall Switch Dimmer, you can unlink them as follows:
Step Operation
1
Tap the Decora-style rocker switch on the desired HAI UPB™ Wall Switch Dimmer(s) five (5) times quickly.
2
The HAI UPB™ Wall Switch Dimmer will flash its lighting load one time and blink its LED blue, to indicate that it is
ready to be unlinked.
3
Press the pushbutton on the HAI UPB™ 8-Button House Controller ten (10) times quickly.
4
Each HAI UPB™ Wall Switch will flash its lighting load one time to indicate that it is successfully unlinked.
Toggling Lighting Loads
After the pushbuttons have been linked, when a pushbutton is pressed while its LED indicator is off, the lighting loads are set to the
preset lighting levels and the LED indicator is turned on. When the pushbutton is pressed again (while its LED indicator is on), the
lighting loads are turn off and the LED indicator is turned off.
Event
When LED Indicator is Off
When LED Indicator is On
Single-Tap The HAI UPB™ Wall Switch Dimmer(s) that are linked to
this pushbutton will go to their preset lighting levels.
The LED indicator under the pushbutton is turned on.
The HAI UPB™ Wall Switch Dimmer(s) that are
linked to this pushbutton will fade to 0% (off).
The LED indicator under the pushbutton is turned off.
Double-Tap The HAI UPB™ Wall Switch Dimmer(s) that are linked to
this pushbutton will snap to 100% (on).
The LED indicator under the pushbutton is turned on.
The HAI UPB™ Wall Switch Dimmer(s) that are
linked to this pushbutton will snap to 0% (off).
The LED indicator under the pushbutton is turned off.
Brightening and Dimming Lighting Loads
When a pushbutton is pressed and held while its LED indicator is off, the lights are brightened, until the pushbutton is released. When
the pushbutton is pressed, the lights are dimmed, until the pushbutton is released.
Event
When LED Indicator is Off
When LED Indicator is On
Hold
The HAI UPB™ Wall Switch Dimmer(s) that are linked to
this pushbutton will brighten.
The LED indicator under the pushbutton is turned on.
The HAI UPB™ Wall Switch Dimmer(s) that are
linked to this pushbutton will dim.
The LED indicator under the pushbutton is turned off.
Release
The HAI UPB™ Wall Switch Dimmer(s) that are linked to
this pushbutton will stop brightening.
The HAI UPB™ Wall Switch Dimmer(s) that are
linked to this pushbutton will stop dimming.
