background image

 

 

 

WaterMax RO Owner’s Manual 

11/13/2012 

25 Year Limited Warranty 

To place the equipment under warranty, the warranty 

registration card must be completed and returned by the original 

owner to the warrantor, Hague Quality Water International, 

within 30 days of installation. 4343 South Hamilton Road. 

Groveport, OH 43125. 

 

Coverage 

This warranty covers specified parts of the Hague WaterMax

®

 

Reverse Osmosis Appliance delivered to the original owner 

when the appliance is purchased for personal, family, or 

household use from an independent Hague dealer. Appliances 

installed in commercial establishments will only qualify for the 

Commercial Three Year Limited Warranty; please refer to form 

#F0105. It is intended to cover defects in workmanship or 

materials or both. 

 

Warrantor’s Performance and Length of Warranty 

Hague Quality Water International warrants that upon receipt 

from the owner of any Hague RO dispensing spigot, filter 

housing and cap, PCF filter housing and cap, membrane 

housing and cap, found to be defective in material or 

workmanship, Hague will repair or replace the defective item, at 

no charge for that item, for 25 YEARS from date of installation. 

 

Hague Quality Water International further warrants that upon 

receipt from the owner of the RO storage tank that is found to be 

defective in material or workmanship, Hague will repair or 

replace the defective item, at no charge, for 5 YEARS from date 

of installation. If the permeate pump and/or auto shut-off valve 

are found to be defective in material or workmanship, Hague will 

repair or replace the defective parts, at no charge for those 

parts, for 2 YEARS from date of installation. If the membrane is 

found to be defective in material or workmanship, Hague will 

repair or replace the defective part for 1 YEAR from date of 

Installation. 

Should a defect or malfunction occur, contact your dealer. If you 

are unable to contact your dealer, then contact Hague Quality 

Water International. 

 

All defective parts must be returned, along with the equipment 

serial number and date of original installation, to an authorized 

Hague dealer or Hague Quality Water International PREPAID, 

and replacement parts will be returned by Hague FREIGHT 

COLLECT. 

 

Further Exclusions and Limitations on Warranty: 

This warranty is null and void unless the Hague Appliance was 

purchased from an independent Hague dealer. 

 

THERE ARE NO WARRANTIES OTHER THAN THOSE 

DESCRIBED IN THIS WARRANTY INSTRUMENT. 

 

This warranty does not cover any service call or labor costs 

incurred with respect to the removal and replacement of any 

defective part or parts. Hague Quality Water International will 

not be liable for, nor will it pay service call or labor charges 

incurred or expended with respect to this warranty. 

 

In the event the water supply being processed through this 

product contains bacterial iron, algae, sulphur, tannins, organic 

matter, or other unusual substances, then unless the appliance 

is represented as being capable of handling these substances in 

the appliance specifications, other special treatment of the water 

supply must be used to remove these substances before they 

enter this product. Otherwise, Hague Quality Water International 

shall have no obligations under this warranty. 

 

This warranty does not cover damage to a part or parts of the 

appliance from causes such as fire, accidents, freezing, or 

unreasonable use, abuse, or neglect by the owner. 

 

This warranty does not cover damage to a part or parts of the 

appliance resulting from improper installation. All plumbing and 

electrical connections should be made in accordance with all 

local codes and the installation instructions provided with the 

appliance. The warranty does not cover damage resulting from 

use with inadequate or defective plumbing; inadequate or 

defective water supply or pressure; inadequate or defective 

house wiring; improper voltage, electrical service, or electrical 

connections; or violation of applicable building, plumbing, or 

electrical codes, laws, ordinances, or regulations. 

 

THIS WARRANTY DOES NOT COVER INCIDENTAL, 

CONSEQUENTIAL, OR SECONDARY DAMAGES. ANY 

IMPLIED WARRANTIES ON THE PRODUCT DESCRIBED IN 

THIS WARRANTY WILL NOT BE EFFECTIVE AFTER THE 

EXPIRATION OF THIS WARRANTY. 

 

No dealer, agent, representative, or other person is authorized 

to extend or expand this limited warranty. 

 

Some states do not allow limitations on how long an implied 

warranty lasts or the exclusion or limitation of incidental or 

consequential damages, so the above limitations and exclusion 

may not apply to you. This warranty gives you specific legal 

rights, and you may also have other rights which vary from state 

to state. 

Содержание WaterMax H5000













































Отзывы: