Installation
The weather station must be installed on a wall or
a vertical post.
Make sure that the weather station is horizontal.
The weather station must be at least 60 cm away
from other elements (buildings, construction parts,
etc.) below, at the side and front.
Installing the support
The weather station TG053A includes a support
for installation on a wall or a vertical post. The
support is clipped to the rear of the unit.
Two articulated supports are available as option
(TG353 and TG354) for wall mounting, on post or
beam.
To remove the base, unscrew the fixing screws
located on right/left-hand base side using a
screwdriver.
Unclip the support by pushing it downwards.
Attach the support vertically on a wall or a post.
Wall
or
vertical
post
HORIZONTAL
The cover of the weather station is clipped to the
lower edge of the unit on the left and right.
Remove the cover of the weather station.
Proceed with care to avoid detaching the cable
between the rain sensor built into the cover and
the electronic circuit board.
Pass the power cables and the KNX bus through
the rubber seals on the lower part of the weather
station, then connect the auxiliary power cables
and the KNX bus (+/-) to the terminals provided.
Installing the weather station
Close the unit by raising the cover on the lower
part. The cover is clipped onto the lower part on
the left and right. A "click" can be heard.
Check that the cover and the lower part are clip-
ped into place !
The illustration shows the closed weather station,
seen from below.
Slide the top of the unit onto the previously ins-
talled support.
The pins on the support are clipped in the rails of
the unit.
Remove the weather station by pulling the unit
upwards until it is unclipped from the support.
Recommendations for installation
Do not open the weather station, otherwise rain
water may enter the unit.
Just a few drops of water can damage the elec-
tronics.
Make sure that the connections are correct.
Incorrect connection can destroy the weather sta-
tion or any connected electronic appliances.
When installing the weather station, make sure
that the temperature sensor (the small plate in the
lower part of the unit) is not damaged. Take care
not to damage the cable between the electronic
board and the rain sensor by pulling or bending it.
The wind speed measurements and the
associated switch outputs only start working 60
seconds after the station is switched on.
Maintenance
Regularly (at least twice a year) check that the
weather station is clean and clean it if
necessary.
Severe soiling can affect the operation of the wind
sensor, provoke permanent rain signals or inhibit
the sun detection function.
Lock
mechanism
For safety reasons, switch off the mains
power supply before servicing or cleaning
the weather station (switch
off the circuit breaker).
Unclip the support
and pull it
upwards
Correct Disposal of this product
(Waste Electrical & Electronic Equipment).
z
(Applicable in the European Union and other European countries with
separate collection systems).
This marking shown on the product or its literature indicates that it should
not be disposed with other household waste at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle
it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this device for environmentally safe recycling.
Business users should contact their supplier and check the terms and condi-
tions of the purchase contract. This product should not be mixed with other
commercial wastes of disposal.
Usable in all Europe
M
and in Switzerland
Half-
crescent
facing
Half-
crescent
facing
Installation on a wall :
Apply the flat side of the support against the wall
with the half-crescent facing upwards.
Preparing the weather station
Installation on a post :
apply the curved side of the support on the post
with the half-crescent facing downwards.
1- Cover with rain sensor.
2- Clicking the cover into place.
3- Lower part of the unit.
60 cm
2
6LE002905A
