2
6E 6023.g
C
A
B
1 3 5
2 4 6 8 10 12 14 16
D
11 13
7 9
Ph
N
As long as the sub-programme is not assigned to
a period, it will not be active and the basic weekly
programme will take place normally.
Electrical connection
Technical specifications
Override programming mode
Pg1... Pg15
The sub-programme is enabled ; enter the next
sub-programme or return to automatic mode or
any other mode by using
.
- by repeatedly pressing key
▶
, consecutive
display of settings of channel A then B,
C and D.
- when this key is held down the settings will
scroll past
- to return to a setting use key
♦
.
All the settings have been read when the number
of steps remaining free is displayed again.
Changing a setting
- choice of mode :
press 3 times, the number
of programme steps remaining free is displayed.
-
▶
press once, the first setting of channel A is
displayed.
- search for the setting to be changed
▶
press
as many times as necessary.
- select the setting by using
♦
.
- select the digit to be altered by using
▶
or
◀
(the selected digit flashes).
- change it by using
♦
.
- confirm this information by pressing repea-
tedly until there is no longer a digit flashing.
After a moment, the next programme step
appears.
Cancelling a setting
- choice of mode :
press 3 times, the number
of programme steps remaining free is displayed.
-
▶
press once, the first setting of channel A is
displayed.
- search for the setting to be changed
▶
press
as many times as necessary.
- erase the setting by using
CI
.
After a moment, the next programme step appears.
Note : a setting applying to different channels
will be erased for all these channels.
This mode allows the programming of 15 wee-
kly cycles different from the basic cycle (sub-
programmes) to be assigned to a given period.
1 - programming of sub-programmes
ex : Pg12, every day of the week at 12. 00
switch on and at 15. 00 switch off channel A
Display mode
A
B
C
D
A
3
1 x
This is the normal operating mode of the set.
- it shows the actual time and date and
the status of the different channels
- it allows manual setting either permanent
or with automatic return of the status of
the outputs (see introduction).
Automatic mode Auto
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
4 x
3 x
2 x
A
B
C
D
A
B
C
D
1 x
2 x
A
B
C
D
4 x
A
B
C
D
A
B
C
D
prg
Pg1...Pg15
date
11 x
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
1
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
A
B
C
D
A
B
C
D
A
B
C
D
3
5
2
1
7
4
6
1
3
5
2
1
7
4
6
A
B
C
D
3
5
2
1
7
4
6
1 x
4 x
1 x
1 x
3 x
2 x
5 x
1 x
1 x
8 x
8 x
Electrical characteristics :
- supply : 230 V
±
10% 50/60 Hz
- consumption : 2 VA
- output : 3 changeover switches and
1 potential-free make contact
μ
10 A - 250 V
쓒
AC1 / 50 000 cycles
1000 W incandescent / 20 000 cycles
Functional characteristics :
- weekly and annual cycle
- programming capacity : 102 steps
(to be distributed over the 4 channels)
- 15 override sub-programmes
- programming precision : 1 minute
- running accuracy :
±
6 min./year
- pulsed operation from 1 to 59 sec.
- operating reserve : Lithium battery.
10 years.
Environment :
- working temperature :
-5 °C to +50 °C
- storage temperature :
-20 °C to +70 °C
Connection capacity :
- flexible : 1 to 6
□
- rigid
: 1,5 to 10
□
selection
of mode
selection of
sub-pro-
gramme
ex : 12
Using of the Data key EG002
This lode permits :
- to store (SAVE) the programme contained in the
time switch.
- to transfer (LOAD) the programme from the
“Data key” to the time switch.
Storage of the programme
(time switch
⇒
Data key)
1 x
1 x
1 x
2 x
Insert the Data key in
the connector
End of storage
Insert the Data key in
the connector
End of transfer
The display
The display
selection
of mode
the number of programme
steps remaining free is
displayed ex : 72 steps
the first
programme step
of channel A
is displayed
EG400
EG001
after about 3 sec., return to automatic mode.
after about 3 sec., return to automatic mode.
Transfer of the programme
(Data key
⇒
time switch)
Write protection of the Data key
Turn data key’s switch into “0” position to lock
the Data key.
The storage is possible in this case.
Failure displays
appears in case of impossible storage
appears in case of unsuccessful reading
(incompatible data key).
The sub-programme Pg12 will replace the basic
weekly from 01.07 to 28.08.
A same sub-programme can be assigned to
several different periods.
When the dates of the start and end of period are
the same, the sub-programme applies only for
that day.
When choosing mode
1X
, the sub-programme
will be erased once it has taken place and will
not be repeated following year.
enter the
group
of days
enter the
group
of days
enter the ON
time
enter the OFF
time
after about 3 sec., return to automatic mode.
2 - allocation of the sub-programme to a period
ex : Pg12, assigned to channel A from 01.07 to 28.08
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
A
B
C
D
prg
Pg1...Pg15
date
7 x
2 x
8 x
1 x
2 x
1 x
6 x
3 x
1 x
11 x
selection
of mode
selection of sub-
programme
ex : 12
enter the first
period
Complete cancellation of programme
- choice of mode :
press 3 times, the number
of programme steps remaining free is displayed.
- when
CI
is pressed for the first time, the num-
ber of programme steps free flashes.
- when pressed for the second time, after a
moment
102 PI
is displayed, all settings have
been erased.
A
B
C
D
5
auto
A
B
C
D
5
auto
1 x
1 x
2 x
1 x
9 x
2 x
1 x
2 x
3 x
2 x
3 x
1 x
1 x
2 x
Change of dates (mode 2)
example : 10.04 and 20.12
Cancellation of summer / winter timetable changes
The summer / winter timetable change is pre-
programmed for the last Sunday in March and
the last Sunday in October (mode 1).
These dates can be altered if necessary (mode
2) or the timetable change can simply be can-
celled (mode 3).
Summer / winter mode
selection
of mode
selection
of mode
enable and
return to
automatic mode
enable and
return to
automatic mode
Hager SAS - 132 bld d’Europe - BP 78 - 67 212 Obernai cedex (FRANCE) - Tél. +333 88 49 50 50 - www.hagergroup.net
This mode enables the programmes set to be
checked, and a setting to be changed or erased.
This mode also enables the programme to be
completely erased.
Programme check
A warranty period of 24 months is offered on hager products,
from date of manufacture, relating to any material of manufac-
turing defect. If any product is found to be defective it must be
returned via the installer and supplier (wholesaler). The warranty
is withdrawn if :
- after inspection by hager quality control dept the device is
found to have been installed in a manner which is contrary to
IEE wiring regulations and accepted practice within the industry
at the time of installation.
- the procedure for the return of goods has not been followed.
Explanation of defect must be included when returning goods.
Warranty
GB
Hager 02.2010
