hager 8300 Series Скачать руководство пользователя страница 10

Страница: 10 / 18

8300 Low Energy Auto-Operator

Installation Instructions

I-EA00257 / 26790910

Rev 2, Rev Date: 1/30/19

Always visit www.hagerco.com for the latest Installation Instructions

HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995

A/C WIRING

Warning:

Ensure all incoming electrical power is shut off before proceeding with any wiring to

Hager 8300 operator. Use only with wire harness provided; failure to do so may

result in damage to equipment or personal harm as well as voiding the warranty.



Connect the main power to the Black / White / Green conector on the back-plate.



Main power supply: 120VAC, 15A, Single Phase, 60hz.



Attach the incoming 120VAC line to the wiring provided in the header shown below.



DO NOT TURN POWER ON until all remaining wiring has been completed.

BLACK:  120VAC Power
WHITE:  Neutral
GREEN:  Ground



Upon applying power, observe the adjustment board LED’s (page 10).



NORMAL OPERATION: DL3 will come on steady and then begin flashing after a few seconds.



FAULTY OPERATION: DL2 will be flashing red. This indicates…



An error condition exists – correct as necessary



Operator requires commissioning – see page 11.

Page 10 of 18

Содержание 8300 Series



















Результаты поиска

Содержание 8300 Series

Отзывы:

Похожие инструкции для 8300 Series

Бренды по названию

Популярные бренды

hager 8300 Series, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 8300 Series

Отзывы:

Похожие инструкции для 8300 Series

Бренды по названию

Популярные бренды